ht500:knowledge-base
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
ht500:knowledge-base [2016/03/22 08:59] Markus Bürgener [Dual extrusion] obsolete info removed |
ht500:knowledge-base [2016/06/28 10:13] Simon Kühling Fix video link |
||
|---|---|---|---|
| Line 46: | Line 46: | ||
| <WRAP clear/> | <WRAP clear/> | ||
| === Wiper check === | === Wiper check === | ||
| - | <WRAP group> | ||
| - | <WRAP half column> | ||
| - | As previously mentioned, the HT500 dual extruder function is exclusively designed for the use with a wiper. The //Wiper Upgrade Kit// is available for 3D printers purchased before July 2015. Hardware revisions later than Rev1.3.0 can be equipped on request with the wiper ex factory.\\ | ||
| - | |||
| - | The following assumes that the wiper has already been installed according to the assembly instructions provided at delivery. If otherwise, find the [[ht500:service-guide#wiper-assembly-and-installation|instructions]] here. | ||
| - | </WRAP> | ||
| - | |||
| - | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:wiper_upgrade.png?400|The Wiper Upgrade Kit provides the necessary hardware for successfully printing dual extruder print jobs.}}] | ||
| - | </WRAP> | ||
| - | </WRAP> | ||
| - | |||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column> | <WRAP half column> | ||
| Line 382: | Line 370: | ||
| __Slic3r part info:__\\ (see [[http://manual.slic3r.org/advanced/repairing-models|Slic3r manual]] also)\\ | __Slic3r part info:__\\ (see [[http://manual.slic3r.org/advanced/repairing-models|Slic3r manual]] also)\\ | ||
| After opening a file in Slic3r, the info box in the bottom-right corner of the plater shows information on the model status. For a single, suitable part the info must look like:\\ | After opening a file in Slic3r, the info box in the bottom-right corner of the plater shows information on the model status. For a single, suitable part the info must look like:\\ | ||
| - | ''Factes: xxxxx (1 shells)''\\ | + | ''Facets: xxxxx (1 shells)''\\ |
| ''Manifold: Yes''\\ | ''Manifold: Yes''\\ | ||
| Line 1307: | Line 1295: | ||
| * Before waisting time on unsuccessful leveling, please rethink if the currently installed nozzle tip is adequate for the print job. Wider nozzles are more tolerant when it comes to compensating leveling mistakes and may be more suited to the task, especially when printing larger parts. | * Before waisting time on unsuccessful leveling, please rethink if the currently installed nozzle tip is adequate for the print job. Wider nozzles are more tolerant when it comes to compensating leveling mistakes and may be more suited to the task, especially when printing larger parts. | ||
| </WRAP> | </WRAP> | ||
| + | |||
| <WRAP half column> | <WRAP half column> | ||
| {{:ht500:leveling_ok.mp4?400|Leveling test is OK}} | {{:ht500:leveling_ok.mp4?400|Leveling test is OK}} | ||
| Line 1413: | Line 1401: | ||
| |''M220 S<print speed multiplier in percent>'' | Increase/decrease print speed of all drive speeds | M220 S95\\ -> decrease print speed to 95 % of g-code value | | |''M220 S<print speed multiplier in percent>'' | Increase/decrease print speed of all drive speeds | M220 S95\\ -> decrease print speed to 95 % of g-code value | | ||
| + | ==== Increasing the minimum detail resolution of the Slic3r ==== | ||
| + | <WRAP group> | ||
| + | <WRAP half column> | ||
| + | - Open your Slic3r in "Expert" mode. | ||
| + | - Open the "Print Settings" tab. | ||
| + | - Choose "Advanced". | ||
| + | - Type the required resolution into the input field "Resolution" in the "Other" frame. We recommended setting the resolution to a value of ''0.05''. | ||
| + | <WRAP clear></WRAP> | ||
| + | </WRAP> | ||
| + | |||
| + | <WRAP half column> | ||
| + | [{{:reprap-industrial-v1:slic3r_minimumres.png?400|}}] | ||
| + | <WRAP info> | ||
| + | INFO | ||
| + | |||
| + | //Increasing the value can help solving the problem of blob formation. As a standard the value is set to "0" since it may cause problems with support structures.// | ||
| + | </WRAP> | ||
| + | </WRAP> | ||
| + | </WRAP> | ||
ht500/knowledge-base.txt · Last modified: 2016/12/05 23:23 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
