ht500:quick-start-guide
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
ht500:quick-start-guide [2016/03/23 11:06] Markus Bürgener very minor changes |
ht500:quick-start-guide [2016/03/23 13:25] Markus Bürgener |
||
|---|---|---|---|
| Line 40: | Line 40: | ||
| </WRAP> | </WRAP> | ||
| + | <WRAP pagebreak></WRAP> | ||
| <WRAP group> | <WRAP group> | ||
| Line 68: | Line 69: | ||
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| + | |||
| + | <WRAP pagebreak></WRAP> | ||
| ===== Safety precautions ===== | ===== Safety precautions ===== | ||
| Line 105: | Line 108: | ||
| In order to ensure your own safety and the proper functioning of your HT500 during operation read and observe the safety instructions in the online documentation. | In order to ensure your own safety and the proper functioning of your HT500 during operation read and observe the safety instructions in the online documentation. | ||
| </WRAP> | </WRAP> | ||
| + | |||
| + | <WRAP pagebreak></WRAP> | ||
| ===== Installation requirements ===== | ===== Installation requirements ===== | ||
| Line 150: | Line 155: | ||
| <WRAP half column> | <WRAP half column> | ||
| * Switch to the **Setup** tab via the respective button in the header. | * Switch to the **Setup** tab via the respective button in the header. | ||
| - | * Write down the web interface URL displayed on the right half of the screen. | + | * Write down the **Web Interface URL** displayed on the right half of the screen. |
| </WRAP> | </WRAP> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{ :reprap-industrial-v1:qsg_setupurl_fullscreen.png?400 |The web interface URL on the SETUP screen is required for connecting the 3D Printer with your local network.}}] | + | [{{ :reprap-industrial-v1:qsg_setupurl_fullscreen.png?400 |The Web Interface URL on the SETUP screen is required for connecting the 3D Printer with your local network.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 160: | Line 165: | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | * Now open your web browser on your PC and enter the web interface URL in the address line and you will be greeted with the **First steps** screen that provides a direct link to the online manual.\\ \\ All further steps are explained in in the Initial Commissioning chapter of the operating manual under [[http://docs.kuehlingkuehling.de/ht500/operation#initial-commissioning]]\\ \\ If you encounter problems with accessing the 3D Printer (or anything else) you may find help in the Troubleshooting section of the online manual\\ ([[http://docs.kuehlingkuehling.de/ht500/troubleshooting]]). | + | * Now open your web browser on your PC and enter the web interface URL in the address line and you will be greeted with the **First Steps** screen that provides a direct link to the online manual.\\ \\ All further steps are explained in in the Initial Commissioning chapter of the operating manual under [[http://docs.kuehlingkuehling.de/ht500/operation#initial-commissioning]]\\ \\ If you encounter problems with accessing the 3D Printer (or anything else) you may find help in the Troubleshooting section of the online manual\\ ([[http://docs.kuehlingkuehling.de/ht500/troubleshooting]]). |
| </WRAP> | </WRAP> | ||
ht500/quick-start-guide.txt · Last modified: 2016/03/24 11:41 by Markus Bürgener
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
