ht500:software-firmware-upgrades
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
ht500:software-firmware-upgrades [2016/03/15 08:44] Markus Bürgener created |
ht500:software-firmware-upgrades [2016/03/18 15:30] Markus Bürgener removed |
||
|---|---|---|---|
| Line 54: | Line 54: | ||
| - [[reprap-industrial-v1:service-guide#exchanging-beaglebone-black-sd-card|Insert the SD card]] into the BeagleBone Black inside the electronics enclosure. | - [[reprap-industrial-v1:service-guide#exchanging-beaglebone-black-sd-card|Insert the SD card]] into the BeagleBone Black inside the electronics enclosure. | ||
| - If not running, power-up your HT500. | - If not running, power-up your HT500. | ||
| - | - Verify all software components are running in the new versions as expected in the [[software-version-v1.1.0-operation-and-commissioning#setup|[Setup]]] tab from the touchscreen menu. | + | - Verify all software components are running in the new versions as expected in the [[operation#setup|[Setup]]] tab from the touchscreen menu. |
| - | - Configure your Filament and Preheating Profiles in the [[software-version-v1.1.0-operation-and-commissioning#configuration|[Configuration]]] tab in the touchscreen menu. | + | - Configure your Filament and Preheating Profiles in the [[operation#configuration|[Configuration]]] tab in the touchscreen menu. |
| - Go to the [[https://github.com/kuehlingkuehling/RepRap-Industrial-Slic3r-profiles/releases|HT500 Slic3r Profile Bundle Repository]] and download the latest profile bundle **that is compatible with your hardware revision and the new firmware version** (see compatibility notes for each profile bundle release). | - Go to the [[https://github.com/kuehlingkuehling/RepRap-Industrial-Slic3r-profiles/releases|HT500 Slic3r Profile Bundle Repository]] and download the latest profile bundle **that is compatible with your hardware revision and the new firmware version** (see compatibility notes for each profile bundle release). | ||
| - If necessary upgrade your [[http://slic3r.org|Slic3r]] installation to the version stated in the compatibility notes for the profile bundle you just downloaded. | - If necessary upgrade your [[http://slic3r.org|Slic3r]] installation to the version stated in the compatibility notes for the profile bundle you just downloaded. | ||
| Line 74: | Line 74: | ||
| The upgrade process is now complete. To prepare your 3D printer for operation, the following calibration tasks are recommended: | The upgrade process is now complete. To prepare your 3D printer for operation, the following calibration tasks are recommended: | ||
| * [[service-guide#backlash-calibration|Backlash calibration]] | * [[service-guide#backlash-calibration|Backlash calibration]] | ||
| - | * Extruder Offset calibration (from the [[software-version-v1.1.0-operation-and-commissioning#setup|[Setup]]] tab on the touchscreen menu) | + | * Extruder Offset calibration (from the [[operation#setup|[Setup]]] tab on the touchscreen menu) |
| ==== Upgrade Instructions for Hardware Revision 1.1.0 ==== | ==== Upgrade Instructions for Hardware Revision 1.1.0 ==== | ||
| - | Before starting the upgrade, open the web-interface of your HT500, select the [[software-version-v1.1.0-operation-and-commissioning#setup|[Setup]]] tab and write down the following values from the EEPROM editor: | + | Before starting the upgrade, open the web-interface of your HT500, select the [[operation#setup|[Setup]]] tab and write down the following values from the EEPROM editor: |
| * //X backlash [mm]// | * //X backlash [mm]// | ||
| * //Y backlash [mm]// | * //Y backlash [mm]// | ||
| Line 88: | Line 88: | ||
| - [[service-guide#exchanging-beaglebone-black-sd-card|Insert the SD card]] into the BeagleBone Black inside the electronics enclosure | - [[service-guide#exchanging-beaglebone-black-sd-card|Insert the SD card]] into the BeagleBone Black inside the electronics enclosure | ||
| - If not running, power-up your HT500 | - If not running, power-up your HT500 | ||
| - | - Verify all software components are running in the new versions as expected in the [[software-version-v1.1.0-operation-and-commissioning#setup|[Setup]]] tab from the touchscreen menu | + | - Verify all software components are running in the new versions as expected in the [[operation#setup|[Setup]]] tab from the touchscreen menu |
| - | - Configure your Filament and Preheating Profiles in the [[software-version-v1.1.0-operation-and-commissioning#configuration|[Configuration]]] tab in the touchscreen menu | + | - Configure your Filament and Preheating Profiles in the [[operation#configuration|[Configuration]]] tab in the touchscreen menu |
| - Go to the [[https://github.com/kuehlingkuehling/RepRap-Industrial-Slic3r-profiles/releases|HT500 Slic3r Profile Bundle Repository]] and download the latest profile bundle **that is compatible with your hardware revision and the new firmware version** (see compatibility notes for each profile bundle release) | - Go to the [[https://github.com/kuehlingkuehling/RepRap-Industrial-Slic3r-profiles/releases|HT500 Slic3r Profile Bundle Repository]] and download the latest profile bundle **that is compatible with your hardware revision and the new firmware version** (see compatibility notes for each profile bundle release) | ||
| - If necessary upgrade your [[http://slic3r.org|Slic3r]] installation to the version stated in the compatibility notes for the profile bundle you just downloaded | - If necessary upgrade your [[http://slic3r.org|Slic3r]] installation to the version stated in the compatibility notes for the profile bundle you just downloaded | ||
| Line 106: | Line 106: | ||
| </WRAP> | </WRAP> | ||
| - | The upgrade process is now complete. To prepare your 3D printer for operation, open the web-interface again on the [[software-version-v1.1.0-operation-and-commissioning#setup|[Setup]]] tab and enter the values you have written down ealier into their corresponding fields: | + | The upgrade process is now complete. To prepare your 3D printer for operation, open the web-interface again on the [[operation#setup|[Setup]]] tab and enter the values you have written down ealier into their corresponding fields: |
| * //X backlash [mm]// | * //X backlash [mm]// | ||
| * //Y backlash [mm]// | * //Y backlash [mm]// | ||
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
