ht500:technical-data
This is an old revision of the document!
Technical Data HT500
Hardware revision v1.4.x
General / Dimensions / Weights
| Housing | aluminum-profile framework acrylic glass integrated LED lighting |
| Positioning system | extruder head mounted on belt driven H-frame (X/Y-axis) screw driven print table (Z-axis) semi-automatic three-point print bed leveling |
| 3D printing technology | Fused Filament Fabrication (FFF) |
| Length | 800mm |
| Width | 600mm |
| Height | 800mm |
| Weight | 49kg (empty) |
| Connection cable | 1.000mm w. Schuko plug and IEC connector |
| Network | Ethernet 10/100, RJ45 |
Temperatures
| Extrusion temperature | max. +500°C |
| Print bed temperature | max. +130°C |
| Print chamber temperature | max. +70°C |
Hot ends
| Screwable M6 brass nozzles A/F8 (included in delivery) | Bore diameter [mm] | Recommended layer height First layer / following |
| 2×0.25 | 0.25 / 0.10 - 0.20 | |
| 2×0.35¹ | 0.35 / 0.10 - 0.28 | |
| 1×0.50² | 0.50 / 0.20 - 0.40 | |
| 1×0.75 | 0.60 / 0.25 - 0.60 |
¹ Installed on the left hot end at delivery and preset in the Slic3r profiles available at the GitHub repository for single and dual extruder prints.
² Installed on the right hot end at delivery and preset in the Slic3r profiles available at the GitHub repository for support material in dual extruder prints.
| Print volume | 200x185x280mm (10.4 liter) |
| Extruder head | dual extruder with two separate extruder nozzles for multi-colored and/or multi-material printing |
| Print bed | exchangeable 210x210mm PEI/glass fabric/carbon composite sheet |
| Minimum layer resolution | 0.1mm |
| Reproduction accuracy | ±0.1mm |
| Tolerance | ±0.1mm |
Material
| Printable materials | ABS, PLA, HIPS, PVA, PC, PA12, PET, PEEK, PP, POM |
| Filament diameter | 2.85±0.1mm |
| Available filament qty. | 0.75kg spool (200x55mm) 2.30kg spool (296x100mm) |
Power and Electronics
| Power consumption (total) | approx. 800W |
| Power supply unit | 1050W, 100 … 240V(AC) input with power plug and main switch 13-6.5A 50/60Hz 12V(DC) connector panel |
| Drives | 3x 1.2A stepper motor (XYZ positioning drives) |
| 2x 1.2A planetary gear drive stepper motor (extruder drives) | |
| Positioning step-width axes | X=0.028mm Y=0.019mm Z=0.003mm |
| Hot ends | 12V, 24W ceramic heating cartridge per hot end |
| Print bed heating | 170W wired silicone heating pad |
| Chamber heating | 4x 170W heating resistor (two per heating element) |
| Chamber lighting | 2x 4W LED array, 6.500K |
| Stand-alone operating module | integrated capacitive 10” touchscreen controller |
| Integrated computer | BeagleBone Black |
| Machine control | RUMBA microprocessor board |
| Load switching | 5x 15A MOSFET board |
| Fans | 3x 119x119x25mm, 12V, 140m³/h axial fan (heat chamber circulation and cooling system) |
| 1x 80x80x25, 12V, 33m³/h axial fan (air filter) |
Sensors
| Limit switch H-frame (X/Y) and print table (Z) | magnetic hall endstops |
| Filament end recognition | mechanic limit switch |
| Temperature sensors hot ends | 800°C thermocouple |
| Temperature sensors print table, print chamber | 300°C thermistors |
Closed loop water cooling system
| Pump | 12V(DC) circulation pump with integrated compensation reservoir |
| Throughput | approx. 210l/h |
| Radiator | 120mm full copper radiator |
| Fan | see electronics |
| Hose diameter | G1/4” |
| Coolant | Innovatek Protect IP ready-to-use |
| Coolant qty. | approx. 250ml |
Air filter
| Air filter | fan duct with exchangeable activated charcoal container |
| Fan | see electronics |
| Filling | 10g, Ø4mm activated charcoal granules |
Ambient conditions
| Operating temperature | +18°C … +27°C |
| Storage temperature | +5°C … +35°C |
| Rel. air humidity | max. 70% |
| Setup site | no excessive formation of dust (e.g. near woodworks, CNC machining centers) |
ht500/technical-data.1458058722.txt.gz · Last modified: 2016/03/15 16:18 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
