User Tools

Site Tools


reprap-industrial-v1:knowledge-base

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
reprap-industrial-v1:knowledge-base [2015/11/17 14:43]
Markus Bürgener [Print bed leveling]
reprap-industrial-v1:knowledge-base [2017/01/18 09:51] (current)
Simon Kühling old revision restored (2016/01/25 13:57)
Line 1007: Line 1007:
 |<100% 25% 55% 20%>| |<100% 25% 55% 20%>|
 ^ Feature ​ ^ Setting ​ ^ see also  ^ ^ Feature ​ ^ Setting ​ ^ see also  ^
-| Print bed design ​   | Standard PEI print bed with ABS glue*  | | +| Print bed design ​   | Standard PEI print bed  | | 
-| Print bed temperature ​ | 120°C ​   | | +| Print bed temperature ​ | First layer: 130°C\\ Layers: ​120°C ​   | | 
-| Build chamber temperature ​ | 70°C   | | +| Build chamber temperature ​ | 75°C   | | 
-| Extruder temperature ​ | 275-280°C ​ | | +| Extruder temperature ​ | First layer 285°C\\ Layers: 275°C ​ | | 
-| Speed settings ​ | use standard presets for ABS  |  [[{|width: 8em}#​Acrylonitrile Butadiene Styrene (ABS)|ABS settings]] ​ | +| Speed settings ​ | Reduce first layer speed to 5mm/s\\ all other settings as standard presets for ABS  |  [[{|width: 8em}#​Acrylonitrile Butadiene Styrene (ABS)|ABS settings]] ​ | 
 | Idler lever preload ​ | 3.5mm   ​| ​ [[{|width: 8em}reprap-industrial-v1:​service-guide#​extruder-idler-lever|Setting the idler lever preload]] ​ | | Idler lever preload ​ | 3.5mm   ​| ​ [[{|width: 8em}reprap-industrial-v1:​service-guide#​extruder-idler-lever|Setting the idler lever preload]] ​ |
  
Line 1020: Line 1020:
 |<100% 25% 55% 20%>| |<100% 25% 55% 20%>|
 ^ Feature ​ ^ Setting ​ ^ see also  ^ ^ Feature ​ ^ Setting ​ ^ see also  ^
-| Solvent ​ | Acetone\\ best results when stirred | | +| Solvent ​ | Acetone\\ best results when stirred ​ | | 
-| Warping ​ | very strong, needs sound contact to the accurately leveled print bed  |  [[{|width: 8em}#​warping-prevention|Warping prevention]] ​ |+| Warping ​ | strong, needs sound contact to the accurately leveled print bed  |  [[{|width: 8em}#​warping-prevention|Warping prevention]] ​ |
 | Stringing ​ | medium ​ | | | Stringing ​ | medium ​ | |
 | Support requirements ​ | Needs support structures for overhangs at 45°. Due to the strong layers, support is hard to remove without breaking delicate structures. ​ | | | Support requirements ​ | Needs support structures for overhangs at 45°. Due to the strong layers, support is hard to remove without breaking delicate structures. ​ | |
Line 1145: Line 1145:
 |<100% 25% 55% 20%>| |<100% 25% 55% 20%>|
 ^ Feature ​ ^ Setting ​ ^ see also  ^ ^ Feature ​ ^ Setting ​ ^ see also  ^
-| Print bed design ​   | standard PEI print bed, glass | | +| Print bed design ​   | standard PEI print bed, glass, [[http://​www.buildtak.eu/​shop/​|BuildTak]] ​| | 
-| Print bed temperature ​ | 40-60°C  ​| ​ | +| Print bed temperature ​ | OFF-50°C  ​| ​ | 
-| Build chamber temperature ​ | 20-40°C ​ ​| ​ [[{|width: 8em}#​adjusting-the-build-chamber-temperature|Build chamber temperature]] ​ | +| Build chamber temperature ​ | OFF°C ​ ​| ​ [[{|width: 8em}#​adjusting-the-build-chamber-temperature|Build chamber temperature]] ​ | 
-| Extruder temperature ​ | 180-235°C ​*  | | +| Extruder temperature ​ | 180-220°C ​*  | | 
-| Speed settings ​ | reduce ​print speed (max. 20m/s for all perimeters) ​*  | |+| Speed settings ​ | reduce ​standard settings ​for ABS by 20% *\\ Perimeters: 20mm/s\\ Infill: 24mm/​s ​ | |
 | Idler lever preload ​ | 4.0mm   ​| ​ [[{|width: 8em}reprap-industrial-v1:​service-guide#​extruder-idler-lever|Setting the idler lever preload]] ​ | | Idler lever preload ​ | 4.0mm   ​| ​ [[{|width: 8em}reprap-industrial-v1:​service-guide#​extruder-idler-lever|Setting the idler lever preload]] ​ |
-| Nozzle tip | 0.5 or above  | |+| Nozzle tip | all  | |
 *<wrap lo> depending on color, filler; test to find best suitable settings for your application.\\ For example: [[http://​colorfabb.com|colorFabb'​s]] famous //​woodfill//​ is best extruded at 225 °C with 12 mm/s for perimeters and 24 mm/s for the infill.</​wrap>​ *<wrap lo> depending on color, filler; test to find best suitable settings for your application.\\ For example: [[http://​colorfabb.com|colorFabb'​s]] famous //​woodfill//​ is best extruded at 225 °C with 12 mm/s for perimeters and 24 mm/s for the infill.</​wrap>​
  
Line 1159: Line 1159:
 | Solvent ​ | Tetrahydrofuran ​ <WRAP caution>​**USE RESPONSIBLY!**\\ //​Tetrahydrofuran can cause eye irritations and irritations of the respiratory system. Fumes are easily flammable.\\ Apply skin protection cream or wear protective gloves when handling the solvent. Do not empty into drains. Do not use near open flames or heat sources.\\ Observe the manufacturer'​s safety data sheet and make accessible to anyone handling tetrahydrofuran!//</​WRAP> ​ | | | Solvent ​ | Tetrahydrofuran ​ <WRAP caution>​**USE RESPONSIBLY!**\\ //​Tetrahydrofuran can cause eye irritations and irritations of the respiratory system. Fumes are easily flammable.\\ Apply skin protection cream or wear protective gloves when handling the solvent. Do not empty into drains. Do not use near open flames or heat sources.\\ Observe the manufacturer'​s safety data sheet and make accessible to anyone handling tetrahydrofuran!//</​WRAP> ​ | |
 | Layer binding ​ | good  | | | Layer binding ​ | good  | |
-| Part strength/​stability ​ | medium ​ | |+| Part strength/​stability ​ | medium; parts are stiff and brittle ​ | |
 | Warping ​ | low   || | Warping ​ | low   ||
 | Drying ​ | not required ​ | | | Drying ​ | not required ​ | |
Line 1216: Line 1216:
  
 ==== Setting a static IP address for RepRap Industrial ethernet connection ==== ==== Setting a static IP address for RepRap Industrial ethernet connection ====
-First, [[#Commandline Access ​to the linux operating system via SSH|establish a commandline connection]] to the printer.+First, [[#commandline-access-to-the-linux-operating-system-via-ssh|establish a commandline connection]] to the printer.
  
 From within the terminal session, edit the network configuration via the command line editor "​nano"​ From within the terminal session, edit the network configuration via the command line editor "​nano"​
Line 1245: Line 1245:
   exit   exit
  
-Shut down (see [[reprap-industrial-v1:​Manual#​Manual control]]) and reboot (power-on button, [[reprap-industrial-v1:Manual#Electronic chamber|11]] in [[reprap-industrial-v1:Manual#Electronic chamber|fig. 4]]the RepRap Industrial to establish the alterations. +[[software-version-v1.1.0-operation-and-commissioning#switching-off-the-3d-printer|Shut down]] and [[software-version-v1.1.0-operation-and-commissioning#waking-from-standby|reboot]] the RepRap Industrial to establish the alterations. 
-<WRAP clear/> ​</​WRAP>​ +<WRAP clear/>
 ==== Use a custom NTP server for time signals ==== ==== Use a custom NTP server for time signals ====
-First, [[#Commandline Access ​to the linux operating system via SSH|establish a commandline connection]] to the printer.+First, [[#commandline-access-to-the-linux-operating-system-via-ssh|establish a commandline connection]] to the printer.
  
 From within the terminal session, stop the NTP daemon background process From within the terminal session, stop the NTP daemon background process
Line 1273: Line 1272:
   exit   exit
  
-Shut down (see [[reprap-industrial-v1:​Manual#​Manual control]]) and reboot (power-on button, [[reprap-industrial-v1:Manual#Electronic chamber|11]] in [[reprap-industrial-v1:Manual#Electronic chamber|fig. 4]]the RepRap Industrial to establish the alterations. +[[software-version-v1.1.0-operation-and-commissioning#switching-off-the-3d-printer|Shut down]] and [[software-version-v1.1.0-operation-and-commissioning#waking-from-standby|reboot]] the RepRap Industrial to establish the alterations. 
-<WRAP clear/> </WRAP>+<WRAP clear/>
  
 ==== Changing Shell Password in the BeagleBone Black Operating System ==== ==== Changing Shell Password in the BeagleBone Black Operating System ====
reprap-industrial-v1/knowledge-base.1447771397.txt.gz · Last modified: 2015/11/17 14:43 (external edit)