reprap-industrial-v1:knowledge-base
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
reprap-industrial-v1:knowledge-base [2016/01/25 13:17] Markus Bürgener [Polylactic Acid (PLA)] |
reprap-industrial-v1:knowledge-base [2017/01/18 09:51] (current) Simon Kühling old revision restored (2016/01/25 13:57) |
||
|---|---|---|---|
| Line 1007: | Line 1007: | ||
| |<100% 25% 55% 20%>| | |<100% 25% 55% 20%>| | ||
| ^ Feature ^ Setting ^ see also ^ | ^ Feature ^ Setting ^ see also ^ | ||
| - | | Print bed design | Standard PEI print bed with ABS glue* | | | + | | Print bed design | Standard PEI print bed | | |
| - | | Print bed temperature | 120°C | | | + | | Print bed temperature | First layer: 130°C\\ Layers: 120°C | | |
| - | | Build chamber temperature | 70°C | | | + | | Build chamber temperature | 75°C | | |
| - | | Extruder temperature | 275-280°C | | | + | | Extruder temperature | First layer 285°C\\ Layers: 275°C | | |
| - | | Speed settings | use standard presets for ABS | [[{|width: 8em}#Acrylonitrile Butadiene Styrene (ABS)|ABS settings]] | | + | | Speed settings | Reduce first layer speed to 5mm/s\\ all other settings as standard presets for ABS | [[{|width: 8em}#Acrylonitrile Butadiene Styrene (ABS)|ABS settings]] | |
| | Idler lever preload | 3.5mm | [[{|width: 8em}reprap-industrial-v1:service-guide#extruder-idler-lever|Setting the idler lever preload]] | | | Idler lever preload | 3.5mm | [[{|width: 8em}reprap-industrial-v1:service-guide#extruder-idler-lever|Setting the idler lever preload]] | | ||
| Line 1020: | Line 1020: | ||
| |<100% 25% 55% 20%>| | |<100% 25% 55% 20%>| | ||
| ^ Feature ^ Setting ^ see also ^ | ^ Feature ^ Setting ^ see also ^ | ||
| - | | Solvent | Acetone\\ best results when stirred. | | | + | | Solvent | Acetone\\ best results when stirred | | |
| - | | Warping | very strong, needs sound contact to the accurately leveled print bed | [[{|width: 8em}#warping-prevention|Warping prevention]] | | + | | Warping | strong, needs sound contact to the accurately leveled print bed | [[{|width: 8em}#warping-prevention|Warping prevention]] | |
| | Stringing | medium | | | | Stringing | medium | | | ||
| | Support requirements | Needs support structures for overhangs at 45°. Due to the strong layers, support is hard to remove without breaking delicate structures. | | | | Support requirements | Needs support structures for overhangs at 45°. Due to the strong layers, support is hard to remove without breaking delicate structures. | | | ||
| Line 1149: | Line 1149: | ||
| | Build chamber temperature | OFF°C | [[{|width: 8em}#adjusting-the-build-chamber-temperature|Build chamber temperature]] | | | Build chamber temperature | OFF°C | [[{|width: 8em}#adjusting-the-build-chamber-temperature|Build chamber temperature]] | | ||
| | Extruder temperature | 180-220°C * | | | | Extruder temperature | 180-220°C * | | | ||
| - | | Speed settings | standard settings for ABS; for filled materials, reduce speed * | | | + | | Speed settings | reduce standard settings for ABS by 20% *\\ Perimeters: 20mm/s\\ Infill: 24mm/s | | |
| | Idler lever preload | 4.0mm | [[{|width: 8em}reprap-industrial-v1:service-guide#extruder-idler-lever|Setting the idler lever preload]] | | | Idler lever preload | 4.0mm | [[{|width: 8em}reprap-industrial-v1:service-guide#extruder-idler-lever|Setting the idler lever preload]] | | ||
| | Nozzle tip | all | | | | Nozzle tip | all | | | ||
reprap-industrial-v1/knowledge-base.1453727853.txt.gz · Last modified: 2016/01/25 13:17 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
