reprap-industrial-v1:manual
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
reprap-industrial-v1:manual [2015/12/11 08:46] Markus Bürgener [Electronic chamber] |
reprap-industrial-v1:manual [2016/07/08 08:02] (current) Simon Kühling [Warranty terms] Update to GmbH |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ====== General ====== | ====== General ====== | ||
| - | Welcome to the RepRap Industrial 3D printer operating manual of the Jonas Kühling & Simon Kühling GbR (in the following referred to as //Kühling&Kühling//).\\ | + | Welcome to the RepRap Industrial 3D printer operating manual of the Kühling&Kühling GmbH (in the following referred to as //Kühling&Kühling//).\\ |
| The RepRap Industrial 3D printer (in the following referred to as //RepRap Industrial//, //3D printer// or //apparatus//) is a fully automatic stand-alone device for **F**used-**F**ilament-**F**abrication (FFF) in a lab or commercial environment.\\ Any information needed for [[#setup-and-installation|installing and commissioning]], [[#touchscreen-operation|operating]], [[#troubleshooting|]], [[service-guide|maintenance and repair]] of the 3D printer are described in the following paragraphs and the accompanying sites.\\ | The RepRap Industrial 3D printer (in the following referred to as //RepRap Industrial//, //3D printer// or //apparatus//) is a fully automatic stand-alone device for **F**used-**F**ilament-**F**abrication (FFF) in a lab or commercial environment.\\ Any information needed for [[#setup-and-installation|installing and commissioning]], [[#touchscreen-operation|operating]], [[#troubleshooting|]], [[service-guide|maintenance and repair]] of the 3D printer are described in the following paragraphs and the accompanying sites.\\ | ||
| This user's manual must be read thoroughly as it is meant to provide the operator with all information needed to operate the RepRap Industrial safely and reasonably. Please always provide access to the website for any user of the 3D printer in case of questions or problems. | This user's manual must be read thoroughly as it is meant to provide the operator with all information needed to operate the RepRap Industrial safely and reasonably. Please always provide access to the website for any user of the 3D printer in case of questions or problems. | ||
| Line 71: | Line 71: | ||
| ===== Warranty terms ===== | ===== Warranty terms ===== | ||
| - | The general [[http://www.kuehlingkuehling.de/terms/|terms and conditions]] of Jonas Kühling & Simon Kühling GbR apply. The customer is familiar with these terms latest on the day of signing the purchase contract. | + | The general [[http://www.kuehlingkuehling.de/terms/|terms and conditions]] of Kühling&Kühling GmbH apply. The customer is familiar with these terms latest on the day of signing the purchase contract. |
| The warranty terms and the liability period can be found in the contract documents and in the order confirmation. | The warranty terms and the liability period can be found in the contract documents and in the order confirmation. | ||
| Line 738: | Line 738: | ||
| The transport box is made of unfinished plywood and may hold splinters and sharp edges that can cause cutting injuries. | The transport box is made of unfinished plywood and may hold splinters and sharp edges that can cause cutting injuries. | ||
| * Take care when removing the transport packaging and wear protective gloves. | * Take care when removing the transport packaging and wear protective gloves. | ||
| + | </WRAP> | ||
| + | |||
| + | <WRAP note> | ||
| + | NOTE | ||
| + | |||
| + | If the 3D Printer has a temperature below 16°C (e.g. directly after delivery in cold weather) there is a danger of air humidity condensing on sensitive electronic components. This can lead to severe damages due to short circuiting during commissioning.\\ Therefore, it is necessary to let the 3D Printer warm up to ambient temperature at its operating place prior to commissioning.\\ Regard the [[technical-data#td-ac|ambient conditions]] required for operation. | ||
| </WRAP> | </WRAP> | ||
| Line 843: | Line 849: | ||
| ====== Imprint ====== | ====== Imprint ====== | ||
| - | //Jonas Kühling & Simon Kühling GbR\\ | + | // Kühling&Kühling GmbH\\ |
| - | Im Wiesengrund 23\\ | + | Christianspries 30\\ |
| - | 24113 Molfsee\\ | + | 24159 Kiel\\ |
| Deutschland\\ | Deutschland\\ | ||
| E-Mail: office@kuehlingkuehling.de\\ | E-Mail: office@kuehlingkuehling.de\\ | ||
| Tel.: +49 (0) 431 98 35 24 73\\ | Tel.: +49 (0) 431 98 35 24 73\\ | ||
| \\ | \\ | ||
| - | Handelsregister\\ | + | Local Court: Amtsgericht Kiel\\ |
| - | USt.-Ident.-Nr.: DE283006938\\ | + | Commercial Register No.: HRB 17535\\ |
| - | WEEE-Reg.-Nr.: DE 11304600\\ | + | Managing Directors: Jonas Kühling, Simon Kühling, Karsten Wenige\\ |
| - | \\ | + | VAT Reg.No.: DE305873054 |
| - | Geschäftsführer\\ | + | |
| - | Jonas Kühling\\ | + | |
| - | Simon Kühling// | + | |
reprap-industrial-v1/manual.1449823590.txt.gz · Last modified: 2015/12/11 08:46 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
