reprap-industrial-v1:manual
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
reprap-industrial-v1:manual [2016/01/22 09:44] Markus Bürgener [Unpacking the machine] |
reprap-industrial-v1:manual [2016/07/08 08:02] (current) Simon Kühling [Warranty terms] Update to GmbH |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ====== General ====== | ====== General ====== | ||
| - | Welcome to the RepRap Industrial 3D printer operating manual of the Jonas Kühling & Simon Kühling GbR (in the following referred to as //Kühling&Kühling//).\\ | + | Welcome to the RepRap Industrial 3D printer operating manual of the Kühling&Kühling GmbH (in the following referred to as //Kühling&Kühling//).\\ |
| The RepRap Industrial 3D printer (in the following referred to as //RepRap Industrial//, //3D printer// or //apparatus//) is a fully automatic stand-alone device for **F**used-**F**ilament-**F**abrication (FFF) in a lab or commercial environment.\\ Any information needed for [[#setup-and-installation|installing and commissioning]], [[#touchscreen-operation|operating]], [[#troubleshooting|]], [[service-guide|maintenance and repair]] of the 3D printer are described in the following paragraphs and the accompanying sites.\\ | The RepRap Industrial 3D printer (in the following referred to as //RepRap Industrial//, //3D printer// or //apparatus//) is a fully automatic stand-alone device for **F**used-**F**ilament-**F**abrication (FFF) in a lab or commercial environment.\\ Any information needed for [[#setup-and-installation|installing and commissioning]], [[#touchscreen-operation|operating]], [[#troubleshooting|]], [[service-guide|maintenance and repair]] of the 3D printer are described in the following paragraphs and the accompanying sites.\\ | ||
| This user's manual must be read thoroughly as it is meant to provide the operator with all information needed to operate the RepRap Industrial safely and reasonably. Please always provide access to the website for any user of the 3D printer in case of questions or problems. | This user's manual must be read thoroughly as it is meant to provide the operator with all information needed to operate the RepRap Industrial safely and reasonably. Please always provide access to the website for any user of the 3D printer in case of questions or problems. | ||
| Line 71: | Line 71: | ||
| ===== Warranty terms ===== | ===== Warranty terms ===== | ||
| - | The general [[http://www.kuehlingkuehling.de/terms/|terms and conditions]] of Jonas Kühling & Simon Kühling GbR apply. The customer is familiar with these terms latest on the day of signing the purchase contract. | + | The general [[http://www.kuehlingkuehling.de/terms/|terms and conditions]] of Kühling&Kühling GmbH apply. The customer is familiar with these terms latest on the day of signing the purchase contract. |
| The warranty terms and the liability period can be found in the contract documents and in the order confirmation. | The warranty terms and the liability period can be found in the contract documents and in the order confirmation. | ||
| Line 743: | Line 743: | ||
| NOTE | NOTE | ||
| - | At ambient temperatures below 16°C air humidity may condensate inside the electronic chamber when the 3D Printer is warmed too quickly.\\ To avoid damages to the electronic components due to condensated water, set up the 3D Printer at its operating place and wait at least 24 hours prior to commissioning so that any moisture may evaporate.\\ Regard the [[technical-data#td-ac|ambient conditions]] required for operation. | + | If the 3D Printer has a temperature below 16°C (e.g. directly after delivery in cold weather) there is a danger of air humidity condensing on sensitive electronic components. This can lead to severe damages due to short circuiting during commissioning.\\ Therefore, it is necessary to let the 3D Printer warm up to ambient temperature at its operating place prior to commissioning.\\ Regard the [[technical-data#td-ac|ambient conditions]] required for operation. |
| </WRAP> | </WRAP> | ||
| Line 849: | Line 849: | ||
| ====== Imprint ====== | ====== Imprint ====== | ||
| - | //Jonas Kühling & Simon Kühling GbR\\ | + | // Kühling&Kühling GmbH\\ |
| - | Im Wiesengrund 23\\ | + | Christianspries 30\\ |
| - | 24113 Molfsee\\ | + | 24159 Kiel\\ |
| Deutschland\\ | Deutschland\\ | ||
| E-Mail: office@kuehlingkuehling.de\\ | E-Mail: office@kuehlingkuehling.de\\ | ||
| Tel.: +49 (0) 431 98 35 24 73\\ | Tel.: +49 (0) 431 98 35 24 73\\ | ||
| \\ | \\ | ||
| - | Handelsregister\\ | + | Local Court: Amtsgericht Kiel\\ |
| - | USt.-Ident.-Nr.: DE283006938\\ | + | Commercial Register No.: HRB 17535\\ |
| - | WEEE-Reg.-Nr.: DE 11304600\\ | + | Managing Directors: Jonas Kühling, Simon Kühling, Karsten Wenige\\ |
| - | \\ | + | VAT Reg.No.: DE305873054 |
| - | Geschäftsführer\\ | + | |
| - | Jonas Kühling\\ | + | |
| - | Simon Kühling// | + | |
reprap-industrial-v1/manual.1453455863.txt.gz · Last modified: 2016/01/22 09:44 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
