reprap-industrial-v1:manual
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
reprap-industrial-v1:manual [2015/09/15 05:44] Markus Bürgener [Storage] spell check |
reprap-industrial-v1:manual [2016/07/08 08:02] (current) Simon Kühling [Warranty terms] Update to GmbH |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ====== General ====== | ====== General ====== | ||
| - | Welcome to the RepRap Industrial 3D printer operating manual of the Jonas Kühling & Simon Kühling GbR (in the following referred to as //Kühling&Kühling//).\\ | + | Welcome to the RepRap Industrial 3D printer operating manual of the Kühling&Kühling GmbH (in the following referred to as //Kühling&Kühling//).\\ |
| - | The RepRap Industrial 3D printer (in the following referred to as //RepRap Industrial//, //3D printer// or //apparatus//) is a fully automatic stand-alone device for **F**used-**F**ilament-**F**abrication (FFF) in a lab or commercial environment.\\ Any information needed for [[#setup-and-installation|installing and commissioning]], [[#touchscreen-operation|operating]], [[#troubleshooting|]], [[service-Guide|maintenance and repair]] of the 3D printer are described in the following paragraphs and the accompanying sites.\\ | + | The RepRap Industrial 3D printer (in the following referred to as //RepRap Industrial//, //3D printer// or //apparatus//) is a fully automatic stand-alone device for **F**used-**F**ilament-**F**abrication (FFF) in a lab or commercial environment.\\ Any information needed for [[#setup-and-installation|installing and commissioning]], [[#touchscreen-operation|operating]], [[#troubleshooting|]], [[service-guide|maintenance and repair]] of the 3D printer are described in the following paragraphs and the accompanying sites.\\ |
| This user's manual must be read thoroughly as it is meant to provide the operator with all information needed to operate the RepRap Industrial safely and reasonably. Please always provide access to the website for any user of the 3D printer in case of questions or problems. | This user's manual must be read thoroughly as it is meant to provide the operator with all information needed to operate the RepRap Industrial safely and reasonably. Please always provide access to the website for any user of the 3D printer in case of questions or problems. | ||
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
| Line 19: | Line 19: | ||
| ===== Valid Version ===== | ===== Valid Version ===== | ||
| ==== Hardware revisions ==== | ==== Hardware revisions ==== | ||
| - | Revision v1.3.0 (current)\\ | + | <WRAP group> |
| - | Revision v1.1.0\\ | + | <WRAP half column> |
| - | Revision v1.0.0 | + | |<100% 33% 33% 33%>| |
| + | ^ Number of revision ^ from ^ until ^ | ||
| + | | v1.3.x | 04-2015 | current | | ||
| + | | v1.2.x | 12-2014 | 04-2015 | | ||
| + | | v1.1.x | 09-2014 | 12-2014 | | ||
| + | | v1.0.x | 02-2014 | 09-2014 | | ||
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
| - | <wrap lo>Check the [[#Electronic chamber|type plate]] for the valid hardware revision of your RepRap Industrial. Beginning with [[reprap-industrial-v1/software-version-v1.1.0-operation-and-commissioning|RepRapOnRails v1.1.0]], you will also find the valid hardware revision in the //[[software-version-v1.1.0-operation-and-commissioning#setup-screen|Setup]]// menu of the GUI.</wrap> | + | The type plate on the of the RepRap Industrial's [[#desc_ec_8|rear side]] you find all information to precisely identify your 3D printer: |
| - | ==== Software versions ==== | + | * Serial number |
| + | * Date of manufacturing | ||
| + | * Hardware Revision¹ | ||
| - | //RepRapOnRails// versions v1.3.1 (current)\\ | + | ¹<wrap lo> Starting with version **1.1.0** of the [[software-version-v1.1.0-operation-and-commissioning| operating software RepRapOnRails]] you will also find the valid hardware revision in the [[software-version-v1.1.0-operation-and-commissioning#setup-menue|[Setup] ]] menu on the touchscreen.</wrap> |
| - | //RepRapOnRails// versions v1.1.0\\ | + | </WRAP> |
| - | //RepRapOnRails// versions v1.0.5 | + | |
| + | <WRAP half column> | ||
| + | [{{:reprap-industrial-v1:typeplate_122015.png?400|Type plate on the rear side.}}] | ||
| + | </WRAP> | ||
| + | </WRAP> | ||
| + | |||
| + | ==== Software versions ==== | ||
| + | Operating sofware:\\ | ||
| + | //RepRapOnRails// Version v1.3.1 -> [[software-version-v1.1.0-operation-and-commissioning|Operating manual]]\\ | ||
| + | //RepRapOnRails// Version v1.1.0 -> [[software-version-v1.1.0-operation-and-commissioning|Operating manual]]\\ | ||
| + | //RepRapOnRails// Version v1.0.5 -> [[reprap-industrial-v1:software-version-v1.0.5-operation-and-commissioning|Operating manual (English only)]]\\ | ||
| + | <WRAP clear></WRAP> | ||
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
| Line 54: | Line 71: | ||
| ===== Warranty terms ===== | ===== Warranty terms ===== | ||
| - | The general [[http://www.kuehlingkuehling.de/terms/|terms and conditions]] of Jonas Kühling & Simon Kühling GbR apply. The customer is familiar with these terms latest on the day of signing the purchase contract. | + | The general [[http://www.kuehlingkuehling.de/terms/|terms and conditions]] of Kühling&Kühling GmbH apply. The customer is familiar with these terms latest on the day of signing the purchase contract. |
| The warranty terms and the liability period can be found in the contract documents and in the order confirmation. | The warranty terms and the liability period can be found in the contract documents and in the order confirmation. | ||
| Line 91: | Line 108: | ||
| The RepRap Industrial 3D printer arrives at your place fully assembled and can be [[#setup-and-initial-commissioning|commissioned]] directly after setting it up and connecting the power supply.\\ | The RepRap Industrial 3D printer arrives at your place fully assembled and can be [[#setup-and-initial-commissioning|commissioned]] directly after setting it up and connecting the power supply.\\ | ||
| The 3D printer is delivered in a wooden transport box on a palette. It is advisable to leave the RepRap Industrial packed and on the palette until moving it to its final installation site for commissioning.\\ | The 3D printer is delivered in a wooden transport box on a palette. It is advisable to leave the RepRap Industrial packed and on the palette until moving it to its final installation site for commissioning.\\ | ||
| - | At the installation site, unpack the RepRap Industrial according to the information in the accompanying **Quick Start Guide**.\\ | + | At the installation site, unpack the RepRap Industrial according to the information in the accompanying **[[quick-start-guide|Quick Start Guide]]**.\\ |
| Dispose of the packaging in accordance with the local waste disposal regulations.\\ | Dispose of the packaging in accordance with the local waste disposal regulations.\\ | ||
| After unpacking, inspect the apparatus for: | After unpacking, inspect the apparatus for: | ||
| Line 116: | Line 133: | ||
| INFO | INFO | ||
| - | //The housing is not designed for subsequently attaching lifting eyes. If you need to transport the 3D printer longer ways, load and secure it on a stable pallet and transport it with a pallet stacker or lifting cart.\\ Detailed information about safeguarding and packing the 3D printer for shipping can be found in the [[service-guide#packing-and-transport-safeguarding|Service guide]].// | + | //The housing is not designed for subsequently attaching lifting eyes. If you need to transport the 3D printer longer ways, load and secure it on a stable pallet and transport it with a pallet stacker or lifting cart.\\ Detailed information about safeguarding and packing the 3D printer for shipping can be found in the [[service-guide#packing-and-transport-safeguarding|Service Guide]].// |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 207: | Line 224: | ||
| If it is necessary to perform works on the cooling system, such as refilling coolant or exchanging defective hoses, avoid direct skin or eye contact. Always wear **adequate protective gloves** that are resistant to chemical substances (e.g. PVC, NBR).\\ | If it is necessary to perform works on the cooling system, such as refilling coolant or exchanging defective hoses, avoid direct skin or eye contact. Always wear **adequate protective gloves** that are resistant to chemical substances (e.g. PVC, NBR).\\ | ||
| Observe the information provided in the manufacturer's safety data sheet. | Observe the information provided in the manufacturer's safety data sheet. | ||
| - | Additional information concerning the cooling system and required maintenance can be found in the [[service-guide#cooling-water-pump|Service guide]].\\ | + | Additional information concerning the cooling system and required maintenance can be found in the [[service-guide#cooling-water-pump|Service Guide]].\\ |
| ==== Emergency stop ==== | ==== Emergency stop ==== | ||
| Line 222: | Line 239: | ||
| When the emergency stop is triggered, the microcontroller board responsible for the stepper motors, heaters and sensors is reset immediately and returns to idle state afterwards. Now it is safe to resolve any problems or defects in the build chamber.\\ | When the emergency stop is triggered, the microcontroller board responsible for the stepper motors, heaters and sensors is reset immediately and returns to idle state afterwards. Now it is safe to resolve any problems or defects in the build chamber.\\ | ||
| \\ | \\ | ||
| - | The build chamber can then be reactivated via the [[software-version-v1.1.0-operation-and-commissioning#print-screen|Print]] screen.\\ Detailed information are provided in the [[software-version-v1.1.0-operation-and-commissioning#emergency-stop|Operating manual]]. | + | The build chamber can then be reactivated via the [[software-version-v1.1.0-operation-and-commissioning#print-screen|[Print] ]] menue.\\ Detailed information are provided in the [[software-version-v1.1.0-operation-and-commissioning#emergency-stop|Operating manual]]. |
| </WRAP> | </WRAP> | ||
| Line 242: | Line 259: | ||
| === Extruder nozzles === | === Extruder nozzles === | ||
| - | The brazen extruder nozzles are sensitive to heat treatment and mechanical strain.\\ If the nozzles tips or extruder barrels are clogged by congealed material, reheating during the normal production flow is utterly sufficient to clear them in most cases.\\ In case you want to change the material type or clogging is effected by foreign particles (i.e. dust grains dragged along with the filament), it is necessary to remove congealed material from the nozzles. The corresponding description can be found in the [[#Cleaning recommendation|cleaning recommendation]]. | + | The brazen extruder nozzles are sensitive to heat treatment and mechanical strain.\\ If the nozzles or extruder barrels are clogged by congealed material, reheating during the normal production flow is utterly sufficient to clear them in most cases.\\ In case you want to change the material type or clogging is effected by foreign particles (i.e. dust grains dragged along with the filament), it is necessary to remove congealed material from the nozzles. The corresponding description can be found in the [[#Cleaning recommendation|cleaning recommendation]]. |
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
| Line 399: | Line 416: | ||
| | 11 | {{anchor:desc_ehc_11:Barrel}} | | | 11 | {{anchor:desc_ehc_11:Barrel}} | | ||
| | 12 | {{anchor:desc_ehc_12:Melter}} | | | 12 | {{anchor:desc_ehc_12:Melter}} | | ||
| - | | 13 | {{anchor:desc_ehc_13:Nozzle (0.35 mm preinstalled at delivery)}} | | + | | 13 | {{anchor:desc_ehc_13:Nozzle (0.35mm preinstalled at delivery)}} | |
| | 14 | {{anchor:desc_ehc_14:Heater}} | | | 14 | {{anchor:desc_ehc_14:Heater}} | | ||
| | 15 | {{anchor:desc_ehc_15:Heating resistor}} | | | 15 | {{anchor:desc_ehc_15:Heating resistor}} | | ||
| Line 418: | Line 435: | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | The nozzle is [[service-guide#changing-the-nozzle-tip|exchangeable]] to provide different bore diameters for different materials, layer thicknesses or print speed. Ex factory, the 0.35 mm tip is preinstalled. Additionally, three nozzle tips with diameters of 0.25 mm, 0.5 mm and 0.75 mm are included. The tips are distinguishable by the engraved markings. | + | The nozzle is [[service-guide#changing-the-nozzle-tip|exchangeable]] to provide different bore diameters for different materials, layer thicknesses or print speed. Ex factory, the 0.35mm tip is preinstalled. Additionally, three nozzles with diameters of 0.25mm, 0.5mm and 0.75mm are included. The tips are distinguishable by the engraved markings. |
| </WRAP> | </WRAP> | ||
| Line 426: | Line 443: | ||
| INFO | INFO | ||
| - | //The 0.35 mm and the 0.5 mm nozzle tips should be used for most purposes and can be driven with an extrusion speed of up to\\ 60 mm/s. The Slic3r profiles that you install during initial commissioning are optimized for the 0.35 mm nozzle tip. Additional information can be found [[reprap-industrial-v1:Tips&Tricks#Slicing|here]] and in the Slic3r manual. Please try and find the settings best suited for your task. Updated and extended Slic3r profiles will be available soon.\\ The 0.75 mm tip is primarily intended for experimental usage and should only be used with a max. extrusion speed of 20 mm/s for a start. Adjust the extrusion speed stepwise until optimized for your needs.\\ The 0.25 mm tip is for filigree, thin walled extrusions. Do not exceed an extrusion speed of 35 mm/s since the material throughput will not suffice for higher speeds.// | + | //The 0.35mm and the 0.5mm nozzles should be used for most purposes and can be driven with an extrusion speed of up to\\ 60mm/s. The Slic3r profiles that you install during initial commissioning are optimized for the 0.35mm nozzle. Additional information can be found in the [[service-guide#changing-the-nozzle-tip|Service Guide]] and in the Slic3r manual. Please try and find the settings best suited for your task. Updated and extended Slic3r profiles will be available soon.\\ The 0.75mm nozzle is primarily intended for experimental usage and should only be used with a max. extrusion speed of 20mm/s for a start. Adjust the extrusion speed stepwise until optimized for your needs.\\ The 0.25mm nozzle is for filigree, thin walled extrusions. Do not exceed an extrusion speed of 35mm/s since the material throughput will not suffice for higher speeds.// |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 448: | Line 465: | ||
| The print table is mounted on the elevator assembly on a 3-point leveling support with set screws, so that the print bed can be height-adjusted for an even and accurate leveling. It is positioned accurate to the millimeter in Z-direction in its useful operating range of 280 mm by the [[#Motors|spindle motor]]. Heating is provided by a flat heating resistor to provide optimal adhesion and even temperature distribution throughout the printing process.\\ | The print table is mounted on the elevator assembly on a 3-point leveling support with set screws, so that the print bed can be height-adjusted for an even and accurate leveling. It is positioned accurate to the millimeter in Z-direction in its useful operating range of 280 mm by the [[#Motors|spindle motor]]. Heating is provided by a flat heating resistor to provide optimal adhesion and even temperature distribution throughout the printing process.\\ | ||
| - | To perform leveling, start the [[software-version-v1.1.0-operation-and-commissioning#setup-screen|Print Bed Leveling]] wizard which will guide you through the process step by step. Additional information on leveling can be found in the [[tips-tricks#print-bed-leveling|Tips & Tricks]] section.\\ | + | To perform leveling, start the [[software-version-v1.1.0-operation-and-commissioning#setup-screen|Print Bed Leveling]] wizard which will guide you through the process step by step. Additional information on leveling can be found in the [[knowledge-base#print-bed-leveling|Knowledgebase]].\\ |
| The print itself will be executed on the polyetherimide (PEI) print bed laid on the print table and fixed with bulldog clamps. In hardware revision 1.0.0 (find the valid hardware revision of your 3D printer on the [[#Electronic chamber|type plate]] the 2.5 mm print bed is held down by two fixedly mounted downholders and two bulldog clamps.\\ With hardware revision 1.1.0 a new, thinner (1.8 mm) print bed is delivered. This could be realized due to the use of other fabrics and provides a more uniform temperature distribution at increased stiffness. The downholders have been replaced with two additional bulldog clamps to allow the use of print beds of different thicknesses.\\ | The print itself will be executed on the polyetherimide (PEI) print bed laid on the print table and fixed with bulldog clamps. In hardware revision 1.0.0 (find the valid hardware revision of your 3D printer on the [[#Electronic chamber|type plate]] the 2.5 mm print bed is held down by two fixedly mounted downholders and two bulldog clamps.\\ With hardware revision 1.1.0 a new, thinner (1.8 mm) print bed is delivered. This could be realized due to the use of other fabrics and provides a more uniform temperature distribution at increased stiffness. The downholders have been replaced with two additional bulldog clamps to allow the use of print beds of different thicknesses.\\ | ||
| The print bed can be exchanged for every print, thus minimizing interruption times during production.\\ | The print bed can be exchanged for every print, thus minimizing interruption times during production.\\ | ||
| Line 523: | Line 540: | ||
| | 5 | Filament inlet with dust wiping sponge | | | 5 | Filament inlet with dust wiping sponge | | ||
| <WRAP clear> </WRAP> | <WRAP clear> </WRAP> | ||
| - | The RepRap Industrial is designed for printing filament strands of a diameter of 2.85 mm with a tolerance of ±0.1 mm. More information about filament and materials can be found in the [[reprap-industrial-v1:knowledge-base#materials|material section]] and the [[reprap-industrial-v1:tips-tricks#filament-quality-check|tips & tricks]] rubric.\\ | + | The RepRap Industrial is designed for printing filament strands of a diameter of 2.85 mm with a tolerance of ±0.1 mm. More information about filament and materials can be found in the [[knowledge-base#materials|material section]] and the [[knowledge-base#filament-quality-check|print preparation section]] of the [[knowledge-base|Knowledgebase]].\\ |
| Two separate strands can be fed from the outside to the extruder head. One filament spool can be positioned on each spool carrier; a stop collar prevents them from falling down due to their rotation.\\ | Two separate strands can be fed from the outside to the extruder head. One filament spool can be positioned on each spool carrier; a stop collar prevents them from falling down due to their rotation.\\ | ||
| The end of the filament strand is manually inserted into the inlet of the feed unit and led through hoses to the two [[#Extruder head components|extruder nozzles]]. At the inlet the filament is put through a sponge that wipes dust off the strand to keep the material unsoiled before reaching the nozzle.\\ | The end of the filament strand is manually inserted into the inlet of the feed unit and led through hoses to the two [[#Extruder head components|extruder nozzles]]. At the inlet the filament is put through a sponge that wipes dust off the strand to keep the material unsoiled before reaching the nozzle.\\ | ||
| Line 549: | Line 566: | ||
| Since hardware revision 1.3.0 the RepRap Industrial 3D printer can be equipped ex factory with a wiper to enable high-quality [[reprap-industrial-v1:knowledge-base#dual-extrusion|dual extruder printing]].\\ | Since hardware revision 1.3.0 the RepRap Industrial 3D printer can be equipped ex factory with a wiper to enable high-quality [[reprap-industrial-v1:knowledge-base#dual-extrusion|dual extruder printing]].\\ | ||
| - | If ordered as an upgrade kit click here to find the [[reprap-industrial-v1:service-guide#wiper-assembly-and-installation|installation instructions]]. | + | If ordered as an upgrade kit click here to find the [[service-guide#wiper-assembly-and-installation|installation instructions]]. |
| </WRAP> | </WRAP> | ||
| Line 574: | Line 591: | ||
| All control elements are installed in the electronic chamber together with the 12 V(DC) mains adapter and the cooling unit.\\ | All control elements are installed in the electronic chamber together with the 12 V(DC) mains adapter and the cooling unit.\\ | ||
| + | |||
| The chamber is completely covered with plastic sheets fastened to the aluminum frame with hexagon socket screws and hammerhead nuts.\\ | The chamber is completely covered with plastic sheets fastened to the aluminum frame with hexagon socket screws and hammerhead nuts.\\ | ||
| The MOSFET power switching board consists of five MOSFETs that switch the four heating resistors of the [[#Build chamber|build chamber]] heating and the heating resistor of the [[#Print table and print bed|print table]].\\ | The MOSFET power switching board consists of five MOSFETs that switch the four heating resistors of the [[#Build chamber|build chamber]] heating and the heating resistor of the [[#Print table and print bed|print table]].\\ | ||
| + | |||
| The RUMBA board (also //reprap microcontroller board//) controls all processes of the printing process, i.e. the drives, the heating resistors, heating fans and the temperature sensors. Exchangeable hardware components are the stepper motor drivers.\\ | The RUMBA board (also //reprap microcontroller board//) controls all processes of the printing process, i.e. the drives, the heating resistors, heating fans and the temperature sensors. Exchangeable hardware components are the stepper motor drivers.\\ | ||
| + | |||
| The BeagleBone Black embedded computer provides the GUI of the [[#Touchscreen|touchscreen]] and the ethernet connection and processes the G-codes of the slicing software.\\ | The BeagleBone Black embedded computer provides the GUI of the [[#Touchscreen|touchscreen]] and the ethernet connection and processes the G-codes of the slicing software.\\ | ||
| Slots in the bottom cover provide an air inlet for the cooling unit. | Slots in the bottom cover provide an air inlet for the cooling unit. | ||
| Line 616: | Line 636: | ||
| At the rear cover you find the mains plug and the main switch of the mains adapter and the RJ45 ethernet plug for the network connection.\\ | At the rear cover you find the mains plug and the main switch of the mains adapter and the RJ45 ethernet plug for the network connection.\\ | ||
| + | |||
| The cooling systems' accumulated warmth is dissipated via the radiator grill to the outside.\\ | The cooling systems' accumulated warmth is dissipated via the radiator grill to the outside.\\ | ||
| - | The type plate is positioned next to the fixing screws of the cooling water pump, providing:\\ {{anchor:serialnumber:the serial number}}\\ the date of manufacturing and {{anchor:hardwarerevision:the hardware revision}}\\ as well as other necessary information about the 3D printer. | + | The [[#hardware-revisions|type plate]] is positioned next to the fixing screws of the cooling water pump. |
| </WRAP> | </WRAP> | ||
| Line 649: | Line 670: | ||
| Find detailed explanations of functions and operating procedures in the [[:reprap-industrial-v1:Software version v1.1.0 - Operation and commissioning|Operating manual]]. | Find detailed explanations of functions and operating procedures in the [[:reprap-industrial-v1:Software version v1.1.0 - Operation and commissioning|Operating manual]]. | ||
| - | In case you experience any trouble, please refer to the [[reprap-industrial-v1:service-guide|Service guide]] and [[reprap-industrial-v1:Troubleshooting|Troubleshooting]]. If you cannot solve a problem with the information given there, you are always welcome to [[http://kuehlingkuehling.de/imprint/|contact us]] personally. We are trying to improve these information constantly and will be grateful for your help when you encounter any previously undescribed faults or problems. | + | In case you experience any trouble, please refer to the [[service-guide|Service guide]] and [[reprap-industrial-v1:Troubleshooting|Troubleshooting]]. If you cannot solve a problem with the information given there, you are always welcome to [[http://kuehlingkuehling.de/imprint/|contact us]] personally. We are trying to improve these information constantly and will be grateful for your help when you encounter any previously undescribed faults or problems. |
| </WRAP> | </WRAP> | ||
| Line 685: | Line 706: | ||
| NOTICE | NOTICE | ||
| - | //The apparatus must not be set up in a surrounding with high formation of dust (e.g. near woodworks etc.). Ingress of particles into the filament supply system can lead to intense cleaning efforts due to clogging of the nozzle tips and thus immense non-productive time.// | + | //The apparatus must not be set up in a surrounding with high formation of dust (e.g. near woodworks etc.). Ingress of particles into the filament supply system can lead to intense cleaning efforts due to clogging of the nozzles and thus immense non-productive time.// |
| </WRAP> | </WRAP> | ||
| <WRAP group> | <WRAP group> | ||
| Line 717: | Line 738: | ||
| The transport box is made of unfinished plywood and may hold splinters and sharp edges that can cause cutting injuries. | The transport box is made of unfinished plywood and may hold splinters and sharp edges that can cause cutting injuries. | ||
| * Take care when removing the transport packaging and wear protective gloves. | * Take care when removing the transport packaging and wear protective gloves. | ||
| + | </WRAP> | ||
| + | |||
| + | <WRAP note> | ||
| + | NOTE | ||
| + | |||
| + | If the 3D Printer has a temperature below 16°C (e.g. directly after delivery in cold weather) there is a danger of air humidity condensing on sensitive electronic components. This can lead to severe damages due to short circuiting during commissioning.\\ Therefore, it is necessary to let the 3D Printer warm up to ambient temperature at its operating place prior to commissioning.\\ Regard the [[technical-data#td-ac|ambient conditions]] required for operation. | ||
| </WRAP> | </WRAP> | ||
| Line 731: | Line 758: | ||
| INFO | INFO | ||
| - | //Find detailed information on repacking the machine for shipping in the [[reprap-industrial-v1:service-guide##packing-and-transport-safeguarding|service guide]].// | + | //Find detailed information on repacking the machine for shipping in the [[service-guide#packing-and-transport-safeguarding|Service Guide]].// |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 809: | Line 836: | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | The RepRap Industrial 3D printer features a low-maintenance design, thus regular maintenance is not required during normal operation. [[service-guide#Cleaning recommendation|Regular cleaning]] will mostly suffice to keep your 3D printer running satisfactorily. In case of faults, refer to the [[Troubleshooting|troubleshooting guide]] and the [[service-guide|service guide]] where most problems known to us and according remedies are lodged. | + | The RepRap Industrial 3D printer features a low-maintenance design, thus regular maintenance is not required during normal operation. [[service-guide#cleaning-recommendation|Regular cleaning]] will mostly suffice to keep your 3D printer running satisfactorily. In case of faults, refer to the [[Troubleshooting|troubleshooting guide]] and the [[service-guide|Service Guide]] where most problems known to us and according remedies are lodged. |
| </WRAP> | </WRAP> | ||
| Line 822: | Line 849: | ||
| ====== Imprint ====== | ====== Imprint ====== | ||
| - | //Jonas Kühling & Simon Kühling GbR\\ | + | // Kühling&Kühling GmbH\\ |
| - | Im Wiesengrund 23\\ | + | Christianspries 30\\ |
| - | 24113 Molfsee\\ | + | 24159 Kiel\\ |
| Deutschland\\ | Deutschland\\ | ||
| E-Mail: office@kuehlingkuehling.de\\ | E-Mail: office@kuehlingkuehling.de\\ | ||
| Tel.: +49 (0) 431 98 35 24 73\\ | Tel.: +49 (0) 431 98 35 24 73\\ | ||
| \\ | \\ | ||
| - | Handelsregister\\ | + | Local Court: Amtsgericht Kiel\\ |
| - | USt.-Ident.-Nr.: DE283006938\\ | + | Commercial Register No.: HRB 17535\\ |
| - | WEEE-Reg.-Nr.: DE 11304600\\ | + | Managing Directors: Jonas Kühling, Simon Kühling, Karsten Wenige\\ |
| - | \\ | + | VAT Reg.No.: DE305873054 |
| - | Geschäftsführer\\ | + | |
| - | Jonas Kühling\\ | + | |
| - | Simon Kühling// | + | |
reprap-industrial-v1/manual.1442295883.txt.gz · Last modified: 2015/09/15 05:44 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
