reprap-industrial-v1:quick-start-guide
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
reprap-industrial-v1:quick-start-guide [2014/10/10 10:33] Markus Bürgener |
reprap-industrial-v1:quick-start-guide [2014/10/28 15:14] Markus Bürgener [Electrical safety] moist environment added |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Quick Start Guide ====== | ====== Quick Start Guide ====== | ||
| + | |||
| Congratulation, you probably just received your RepRap Industrial 3D Printer. Follow these short instructions and you are up and running in no time!\\ \\ | Congratulation, you probably just received your RepRap Industrial 3D Printer. Follow these short instructions and you are up and running in no time!\\ \\ | ||
| You will always find the latest version of the manual, additional documentation and new software releases at\\ | You will always find the latest version of the manual, additional documentation and new software releases at\\ | ||
| Line 12: | Line 12: | ||
| In order to ensure your own safety and the proper functioning of your RepRap Industrial read and observe the following information. | In order to ensure your own safety and the proper functioning of your RepRap Industrial read and observe the following information. | ||
| ==== Electrical safety ==== | ==== Electrical safety ==== | ||
| - | * Only connect the 3D Printer to the specified supply voltage. | + | * Only connect the 3D printer to the specified supply voltage. |
| - | * Do not operate the 3D Printer with defective cable connections. | + | * Do not operate the 3D printer with defective cable connections. |
| + | * Do not setup the 3D printer in a moist environment. | ||
| * Work on the electrical connections and the electrical equipment of the 3D Printer **must only** be carried out by trained personnel. | * Work on the electrical connections and the electrical equipment of the 3D Printer **must only** be carried out by trained personnel. | ||
| ==== Health hazards ==== | ==== Health hazards ==== | ||
| Line 34: | Line 35: | ||
| <WRAP half column> | <WRAP half column> | ||
| ^ No. ^ Description ^ | ^ No. ^ Description ^ | ||
| - | | 1 | touchscreen | | + | | 1 | Touchscreen user interface | |
| - | | 2 | power-on button | | + | | 2 | Power-on button | |
| - | | 3 | main switch | | + | | 3 | Main switch | |
| - | | 4 | mains socket | | + | | 4 | Mains socket | |
| - | | 5 | RJ45 ethernet socket | | + | | 5 | RJ45 ethernet socket | |
| </WRAP> | </WRAP> | ||
| Line 67: | Line 68: | ||
| * Remove all remaining cardboard and blue tape used as transport protection from inside the build chamber. | * Remove all remaining cardboard and blue tape used as transport protection from inside the build chamber. | ||
| * Gently move the print head into the center of the build chamber by hand. | * Gently move the print head into the center of the build chamber by hand. | ||
| - | * Check the entire device carefully for any transportation damage. | + | * Check the entire device carefully for any transportation damage and completeness of delivery. |
| ===== Initial commissioning ===== | ===== Initial commissioning ===== | ||
| Line 154: | Line 155: | ||
| INFO | INFO | ||
| - | The emergency stop function does not provide a cool down sequence. | + | The emergency stop function does not provide a cool down sequence.\\ |
| - | * Do not use the emergency stop button to abort current print jobs, as this may lead to damage of the 3D Printer due to uncontrolled heat accumulation. | + | Do not use the emergency stop button to abort current print jobs, as this may lead to damage of the 3D Printer due to uncontrolled heat accumulation.\\ |
| - | * Do not use the main switch as an emergency stop button. You risk loosing or corrupting data. | + | Do not use the main switch as an emergency stop button. You risk loosing or corrupting data. |
| </WRAP> | </WRAP> | ||
| When the Emergency Stop is triggered, the microcontroller board responsible for the stepper motors, heaters and sensors is reset immediately and returns to idle state afterwards. Now it is safe to resolve any problems or defects in the build chamber. The build chamber can then be reactivated via the //Print// screen or by starting a print job as usual. | When the Emergency Stop is triggered, the microcontroller board responsible for the stepper motors, heaters and sensors is reset immediately and returns to idle state afterwards. Now it is safe to resolve any problems or defects in the build chamber. The build chamber can then be reactivated via the //Print// screen or by starting a print job as usual. | ||
reprap-industrial-v1/quick-start-guide.txt · Last modified: 2016/03/18 14:05 by Markus Bürgener
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
