This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
reprap-industrial-v1:quick-start-guide [2014/10/10 10:34] Markus Bürgener [Emergency stop] |
reprap-industrial-v1:quick-start-guide [2014/10/28 15:19] Markus Bürgener [Damage risks] Stable substructure added |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== Quick Start Guide ====== | ====== Quick Start Guide ====== | ||
+ | |||
Congratulation, you probably just received your RepRap Industrial 3D Printer. Follow these short instructions and you are up and running in no time!\\ \\ | Congratulation, you probably just received your RepRap Industrial 3D Printer. Follow these short instructions and you are up and running in no time!\\ \\ | ||
You will always find the latest version of the manual, additional documentation and new software releases at\\ | You will always find the latest version of the manual, additional documentation and new software releases at\\ | ||
Line 12: | Line 12: | ||
In order to ensure your own safety and the proper functioning of your RepRap Industrial read and observe the following information. | In order to ensure your own safety and the proper functioning of your RepRap Industrial read and observe the following information. | ||
==== Electrical safety ==== | ==== Electrical safety ==== | ||
- | * Only connect the 3D Printer to the specified supply voltage. | + | * Only connect the 3D printer to the specified supply voltage. |
- | * Do not operate the 3D Printer with defective cable connections. | + | * Do not operate the 3D printer with defective cable connections. |
+ | * Do not setup the 3D printer in a moist environment. | ||
* Work on the electrical connections and the electrical equipment of the 3D Printer **must only** be carried out by trained personnel. | * Work on the electrical connections and the electrical equipment of the 3D Printer **must only** be carried out by trained personnel. | ||
==== Health hazards ==== | ==== Health hazards ==== | ||
Line 21: | Line 22: | ||
==== Damage risks ==== | ==== Damage risks ==== | ||
+ | * Make sure the 3D printer is setup on a stable and carrying substructure. Tipping or tumbling will damage exterior and interior components beyond repair. | ||
* Never switch off the machine by flipping the main switch while the system is still running. Always shut down the 3D Printer properly as described in [[quick-start-guide#Shutdown / Wake up]]. | * Never switch off the machine by flipping the main switch while the system is still running. Always shut down the 3D Printer properly as described in [[quick-start-guide#Shutdown / Wake up]]. | ||
- | * Be careful not to damage the print bed. Scratched, broken or buckled print beds can no longer be used for production and must be replaced. | + | * Do not damage the print bed. Scratched, broken or buckled print beds can no longer be used for production and must be replaced. |
- | * Do not use solvents inside the build chamber. Solvent fumes may damage printer components or dissolve printed objects. | + | * Do not use solvents inside the build chamber. Solvent fumes may damage printer components or dissolve printed objects.\\ Always remove the print bed from the build chamber before cleaning it. |
===== Additional information ===== | ===== Additional information ===== | ||
Line 67: | Line 69: | ||
* Remove all remaining cardboard and blue tape used as transport protection from inside the build chamber. | * Remove all remaining cardboard and blue tape used as transport protection from inside the build chamber. | ||
* Gently move the print head into the center of the build chamber by hand. | * Gently move the print head into the center of the build chamber by hand. | ||
- | * Check the entire device carefully for any transportation damage. | + | * Check the entire device carefully for any transportation damage and completeness of delivery. |
===== Initial commissioning ===== | ===== Initial commissioning ===== |