reprap-industrial-v1:quick-start-guide
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
reprap-industrial-v1:quick-start-guide [2014/10/28 12:47] Markus Bürgener [Unpacking / Setting up] |
reprap-industrial-v1:quick-start-guide [2014/12/04 09:43] Markus Bürgener [Initial commissioning] orthography |
||
|---|---|---|---|
| Line 12: | Line 12: | ||
| In order to ensure your own safety and the proper functioning of your RepRap Industrial read and observe the following information. | In order to ensure your own safety and the proper functioning of your RepRap Industrial read and observe the following information. | ||
| ==== Electrical safety ==== | ==== Electrical safety ==== | ||
| - | * Only connect the 3D Printer to the specified supply voltage. | + | * Only connect the 3D printer to the specified supply voltage. |
| - | * Do not operate the 3D Printer with defective cable connections. | + | * Do not operate the 3D printer with defective cable connections. |
| + | * Do not setup the 3D printer in a moist environment. | ||
| * Work on the electrical connections and the electrical equipment of the 3D Printer **must only** be carried out by trained personnel. | * Work on the electrical connections and the electrical equipment of the 3D Printer **must only** be carried out by trained personnel. | ||
| ==== Health hazards ==== | ==== Health hazards ==== | ||
| - | * Due to the production process and depending on the material used for printing, components in the build chamber may reach temperatures up to 300 °C (572 °F). Wear adequate protective gloves, when handling freshly printed objects if you do not wish to cool down the machine between two print jobs. | + | * Due to the production process and depending on the material used for printing, components in the build chamber may reach temperatures up to 300 °C (572 °F). Wear adequate protective gloves or let the 3D printer cool down to avoid burning injuries when handling printed objects. |
| - | * The weight of the RepRap Industrial exceeds 50 kg. Always carry it **two by two**. | + | * The weight of the RepRap Industrial exceeds 50 kg. Always carry it **two by two**.\\ Make sure that the 3D printer cannot tip over or tumble down to avoid crushing injuries. |
| * Use only mild detergents for cleaning. When using solvents to remove filament residues, always regard the safety data sheet of the manufacturer. Wear adequate protective equipment if required. | * Use only mild detergents for cleaning. When using solvents to remove filament residues, always regard the safety data sheet of the manufacturer. Wear adequate protective equipment if required. | ||
| ==== Damage risks ==== | ==== Damage risks ==== | ||
| + | * Make sure the 3D printer is setup on a stable and carrying substructure. Tipping or tumbling will damage exterior and interior components beyond repair. | ||
| * Never switch off the machine by flipping the main switch while the system is still running. Always shut down the 3D Printer properly as described in [[quick-start-guide#Shutdown / Wake up]]. | * Never switch off the machine by flipping the main switch while the system is still running. Always shut down the 3D Printer properly as described in [[quick-start-guide#Shutdown / Wake up]]. | ||
| - | * Be careful not to damage the print bed. Scratched, broken or buckled print beds can no longer be used for production and must be replaced. | + | * Do not damage the print bed. Scratched, broken or buckled print beds can no longer be used for production and must be replaced. |
| - | * Do not use solvents inside the build chamber. Solvent fumes may damage printer components or dissolve printed objects. | + | * Do not use solvents inside the build chamber. Solvent fumes may damage printer components or dissolve printed objects.\\ Always remove the print bed from the build chamber before cleaning it. |
| ===== Additional information ===== | ===== Additional information ===== | ||
| Line 101: | Line 103: | ||
| Adjusting the filament spools. | Adjusting the filament spools. | ||
| - | Depending on the diameter of the filament spool you install, you may have to adjust the spool guides in order to avoid poor conveyance of the filament.\\ The spool guides are preinstalled for fitting the 750 g spools provided for test reasons.\\ To adjust the spool guides: | + | Depending on the diameter of the filament spool you install, you may have to adjust the spool carrier in order to avoid poor conveyance of the filament.\\ The spool carriers are preinstalled for fitting the 750 g spools included in the delivery.\\ To adjust the spool carriers: |
| * Use an Allen wrench size 2.5 to //loosen// the two fixing screws of each spool guide. | * Use an Allen wrench size 2.5 to //loosen// the two fixing screws of each spool guide. | ||
| * Load a new filament spool onto the guide. Observe the direction of rotation. | * Load a new filament spool onto the guide. Observe the direction of rotation. | ||
| Line 128: | Line 130: | ||
| For day-to-day use, the power supply should stay connected to mains power (main switch in position **<I>** (ON). | For day-to-day use, the power supply should stay connected to mains power (main switch in position **<I>** (ON). | ||
| - | ===== Important Information on handling the print bed ===== | + | ===== Important information on handling the print bed ===== |
| The black sheets used as print beds are made of polyetherimide (PEI) glass fabric composite material. This material composition is highly resistant to a lot of solvents. It is particular compatible with acetone and isopropylalcohol.\\ If you experience insufficient adhesion of the printed objects to the print surface during the first prints, it is advisable to thoroughly clean the print bed once with an acetone-soaked lint-free cloth.\\ For further use, regular cleaning is usually not necessary. However, it should be ensured that the surface is always free of grease (i.e. fingerprints). Should grease residues on the surface lead to poor adhesion, the print bed can be degreased with isopropylalcohol.\\ After completion of a print proceed as follows: | The black sheets used as print beds are made of polyetherimide (PEI) glass fabric composite material. This material composition is highly resistant to a lot of solvents. It is particular compatible with acetone and isopropylalcohol.\\ If you experience insufficient adhesion of the printed objects to the print surface during the first prints, it is advisable to thoroughly clean the print bed once with an acetone-soaked lint-free cloth.\\ For further use, regular cleaning is usually not necessary. However, it should be ensured that the surface is always free of grease (i.e. fingerprints). Should grease residues on the surface lead to poor adhesion, the print bed can be degreased with isopropylalcohol.\\ After completion of a print proceed as follows: | ||
| Line 137: | Line 139: | ||
| </WRAP> | </WRAP> | ||
| - | - Remove the two frontal bulldog clamps. | + | * Remove the two frontal bulldog clamps. |
| - | - Remove the print bed from from the print bed table. | + | * Remove the print bed from from the print bed table. |
| - | - Let the print bed cool down to room temperature with the workpiece still attached. Large printed objects are likely to separate themselves from the surface. Smaller objects may be released by gently bending the print bed from different angles and can easily pulled off afterwards. | + | * Let the print bed cool down to room temperature with the workpiece still attached. Large printed objects are likely to separate themselves from the surface. Smaller objects may be released by gently bending the print bed from different angles and can easily pulled off afterwards. |
| - | - If residues of the print material remain on the print bed, use a very sharp, flat mounted blade to scrape the surface clean. Be careful **not to scratch** the print bed. | + | * If residues of the print material remain on the print bed, use a very sharp, flat mounted blade to scrape the surface clean. Be careful **not to scratch** the print bed. |
| <WRAP info> | <WRAP info> | ||
reprap-industrial-v1/quick-start-guide.txt · Last modified: 2016/03/18 14:05 by Markus Bürgener
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
