reprap-industrial-v1:service-guide
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
reprap-industrial-v1:service-guide [2015/07/24 12:22] Markus Bürgener |
reprap-industrial-v1:service-guide [2015/11/02 07:59] Markus Bürgener [Replacing the heating block] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Service guide for RepRap Industrial ====== | + | ====== Service guide for RepRap Industrial ====== |
| The instructions below are meant to enable you to perform troubleshooting, repair and cleaning tasks adequately and without damaging the machine. | The instructions below are meant to enable you to perform troubleshooting, repair and cleaning tasks adequately and without damaging the machine. | ||
| Line 302: | Line 302: | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | Cleaning the hot end nozzle tip is required quite often compared to other components of the 3D printer. Dust ingression through the filament supply system, coking of material, and storage in a dusty place may lead to clogging of the tip's bore.\\ An imprecisely (too closely) leveled print bed, too low extrusion temperatures or too high an extrusion speed can lead the nozzle tip choking itself.\\ | + | Cleaning the hot end nozzle tip is required quite often compared to other components of the 3D printer. Dust ingression through the filament supply system, coking of material, and storage in a dusty place may lead to clogging of the tip's bore.\\ An imprecisely (too closely) leveled print bed, too low extrusion temperatures or too high an extrusion speed can lead to the nozzle tip choking itself.\\ |
| In any of these cases, a decreasing print quality and slipping of the drive gear will be the first visible effects. Removing and cleaning the nozzle tip is then necessary; the [[#Remedying clogging|description below]] should remedy the problem, as long as no hardware defect is present.\\ \\ | In any of these cases, a decreasing print quality and slipping of the drive gear will be the first visible effects. Removing and cleaning the nozzle tip is then necessary; the [[#Remedying clogging|description below]] should remedy the problem, as long as no hardware defect is present.\\ \\ | ||
| Cleaning the extruder hot end barrel is only required if it is clogged with coked material or foreign particles. It is recommended after dissembling the hot end at material change (installing a //different// material). | Cleaning the extruder hot end barrel is only required if it is clogged with coked material or foreign particles. It is recommended after dissembling the hot end at material change (installing a //different// material). | ||
| Line 335: | Line 335: | ||
| * pipe cleaner | * pipe cleaner | ||
| === Additional information === | === Additional information === | ||
| - | * Disassembly / re-installation of nozzle and barrel -> [[#Dissembling / re-installing the hot end nozzle tips and/or barrels|Service guide]] | + | [[{|width: 25em}#dissemblingre-installing-the-hot-end-nozzle-tips-andor-barrels|Disassembly / re-installation of nozzle and barrel]]\\ |
| - | * Suitable solvents -> [[reprap-industrial-v1:knowledge-base#materials|Knowledge base]] | + | [[{|width: 25em}reprap-industrial-v1:knowledge-base#materials|Suitable solvents]]\\ |
| - | * Removing / reinserting filament -> Software manual [[Software version v1.0.5 - Operation and commissioning#Changing the filament|v1.0.5]] or Software manual [[Software version v1.1.0 - Operation and commissioning#Changing the filament|v1.1.0]]; | + | [[{|width: 25em}Software version v1.1.0 - Operation and commissioning#Changing the filament|Changing the filament]] | |
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
| Line 428: | Line 428: | ||
| === Additional information === | === Additional information === | ||
| - | * Software manual [[Software version v1.0.5 - Operation and commissioning#Manual Control|v1.0.5]] | + | [[{|width: 10em}software-version-v1.1.0-operation-and-commissioning#expert-control-screen|Software manual]] |
| - | * Software manual [[Software version v1.1.0 - Operation and commissioning#Print|v1.1.0]] | + | |
| === Removing === | === Removing === | ||
| Line 497: | Line 496: | ||
| === Additional information === | === Additional information === | ||
| {{anchor:sg02}} | {{anchor:sg02}} | ||
| - | * [[#Cleaning recommendation|]] | + | [[{|width: 15em}#Cleaning recommendation|Cleaning recommendation]]\\ |
| - | * Software manual: [[reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc131|filament change]], [[reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc14t05|expert control]] | + | [[{|width: 15em}reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc131|Software manual - filament change]] [[{|width: 15em}reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc14t05|Software manual - expert control]] |
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
| Line 686: | Line 685: | ||
| * Allen wrench #1.5 | * Allen wrench #1.5 | ||
| - | === Accompanying information === | + | === Additional information === |
| - | * Troubleshooting: [[reprap-industrial-v1:troubleshooting#p9|P9]], [[reprap-industrial-v1:troubleshooting#em1|EM1]] | + | [[{|width: 10em}reprap-industrial-v1:troubleshooting#p9|Troubleshooting P9]]\\ |
| + | [[{|width: 10em}reprap-industrial-v1:troubleshooting#em1|Troubleshooting EM1]] | ||
| === Heating block exchange procedure === | === Heating block exchange procedure === | ||
| Line 1148: | Line 1148: | ||
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| + | |||
| + | <WRAP clear></WRAP> | ||
| + | |||
| + | ==== Upgrading to 400°C ==== | ||
| + | In case you ordered the 400°C upgrade kit and are looking for the assembly instructions: these are currently only available as PDF download in German language. The English version will soon be available here. | ||
| + | |||
| + | {{:reprap-industrial-v1:ht400_anschliessen_de_201509.pdf|}} | ||
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
reprap-industrial-v1/service-guide.txt · Last modified: 2017/01/18 09:52 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
