reprap-industrial-v1:service-guide
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
reprap-industrial-v1:service-guide [2015/10/30 15:05] Markus Bürgener [Opening the electronic chamber] |
reprap-industrial-v1:service-guide [2015/11/02 07:56] Markus Bürgener [Changing the nozzle tip] |
||
|---|---|---|---|
| Line 335: | Line 335: | ||
| * pipe cleaner | * pipe cleaner | ||
| === Additional information === | === Additional information === | ||
| - | |<50% 80% 20%>| | + | [[{|width: 25em}#dissemblingre-installing-the-hot-end-nozzle-tips-andor-barrels|Disassembly / re-installation of nozzle and barrel]]\\ |
| - | | Disassembly / re-installation of nozzle and barrel | [[{dev:seealso.png|width: 10em}#dissemblingre-installing-the-hot-end-nozzle-tips-andor-barrels|Service guide]] | | + | [[{|width: 25em}reprap-industrial-v1:knowledge-base#materials|Suitable solvents]]\\ |
| - | | Suitable solvents | [[{dev:seealso.png|width: 10em}reprap-industrial-v1:knowledge-base#materials|Knowledge base]] | | + | [[{|width: 25em}Software version v1.1.0 - Operation and commissioning#Changing the filament|Changing the filament]] | |
| - | | Removing / reinserting filament | Software manual\\ [[{dev:seealso.png|width: 10em}Software version v1.0.5 - Operation and commissioning#Changing the filament|v1.0.5]]\\ [[{dev:seealso.png|width: 10em}Software version v1.1.0 - Operation and commissioning#Changing the filament|v1.1.0]] | | + | |
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
| Line 429: | Line 428: | ||
| === Additional information === | === Additional information === | ||
| - | |<50% 80% 20%>| | + | [[{|width: 10em}software-version-v1.1.0-operation-and-commissioning#expert-control-screen|Software manual]] |
| - | | \\ Software manual | [[{dev:seealso.png|width: 10em}software-version-v1.0.5-operation-and-commissioning#manual-control|v1.0.5]] | | + | |
| - | |::: | [[{dev:seealso.png|width: 10em}software-version-v1.1.0-operation-and-commissioning#expert-control-screen|v1.1.0]] | | + | |
| === Removing === | === Removing === | ||
| Line 499: | Line 496: | ||
| === Additional information === | === Additional information === | ||
| {{anchor:sg02}} | {{anchor:sg02}} | ||
| - | * [[#Cleaning recommendation|]] | + | [[{|width: 15em}#Cleaning recommendation|Cleaning recommendation]]\\ |
| - | * Software manual: [[reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc131|filament change]], [[reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc14t05|expert control]] | + | [[{|width: 15em}reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc131|Software manual - filament change]] [[{|width: 15em}reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc14t05|Software manual - expert control]] |
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
reprap-industrial-v1/service-guide.txt · Last modified: 2017/01/18 09:52 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
