reprap-industrial-v1:service-guide
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
reprap-industrial-v1:service-guide [2015/11/02 07:56] Markus Bürgener [Changing the nozzle tip] |
reprap-industrial-v1:service-guide [2017/01/18 09:52] (current) Simon Kühling old revision restored (2016/03/23 10:54) |
||
|---|---|---|---|
| Line 245: | Line 245: | ||
| ===== Hardware components and manual tasks ===== | ===== Hardware components and manual tasks ===== | ||
| + | ==== Maintenance intervals ==== | ||
| + | === Daily (end of shift) === | ||
| + | |<100% 25% 50% 25%>| | ||
| + | ^ Where ^ What ^ Tools / To Do ^ | ||
| + | | Build chamber | - remove filament residues | brush, hand broom, vacuum cleaner | | ||
| + | |||
| + | |||
| + | === Monthly (150 operating hours) === | ||
| + | |<100% 25% 50% 25%>| | ||
| + | ^ Where ^ What ^ Tools / To Do ^ | ||
| + | | Timing belt | - check the tension; re-tension if required | [[#timing-belt-tension|Description]] | | ||
| + | | Shafts | - check for dryness; lubricate if required | [[#shaft-lubrication|Description]] | | ||
| + | | Cooling circuit | - check hoses for excessive bubbles; refill if required\\ - check hose connectors at the LEDs and the stepper drives for correct positioning; refasten if required | [[#cooling-water-pump|Description]] | | ||
| + | | Dust wiping sponge | - check for cleanliness; clean or replace if required | rinse with fresh water and dry thoroughly | | ||
| + | |||
| + | === Semiannually (1.250 operating hours) === | ||
| + | |<100% 25% 50% 25%>| | ||
| + | ^ Where ^ What ^ Tools / To Do ^ | ||
| + | | Air filter | - exchange filling | [[#air-filter|Description]] | | ||
| + | |||
| + | === Yearly (2.500 operating hours) === | ||
| + | |<100% 25% 50% 25%>| | ||
| + | ^ Where ^ What ^ Tools / To Do ^ | ||
| + | | Z-axis spindle drive | - check for fast seat:\\ with the 3D Printer switched on, grab the print table near the elevator and try to lift it\\ -> play of the table on the spindle requires replacement of the spindle nut\\ -> if you can lift the entire assembly including the spindle, the adjusting rings must be refastened | [[#repositioning-and-refastening-the-z-axis-clamp-collar|Description]] | | ||
| + | <WRAP clear/> | ||
| ==== Cleaning recommendation ==== | ==== Cleaning recommendation ==== | ||
| Line 685: | Line 710: | ||
| * Allen wrench #1.5 | * Allen wrench #1.5 | ||
| - | === Accompanying information === | + | === Additional information === |
| - | * Troubleshooting: [[reprap-industrial-v1:troubleshooting#p9|P9]], [[reprap-industrial-v1:troubleshooting#em1|EM1]] | + | [[{|width: 10em}reprap-industrial-v1:troubleshooting#p9|Troubleshooting P9]]\\ |
| + | [[{|width: 10em}reprap-industrial-v1:troubleshooting#em1|Troubleshooting EM1]] | ||
| === Heating block exchange procedure === | === Heating block exchange procedure === | ||
reprap-industrial-v1/service-guide.1446450985.txt.gz · Last modified: 2015/11/02 07:56 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
