This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
reprap-industrial-v1:technical-data [2016/01/22 09:41] Markus Bürgener |
reprap-industrial-v1:technical-data [2016/07/07 10:20] (current) Simon Kühling |
||
---|---|---|---|
Line 2: | Line 2: | ||
==== Hardware revision v1.0 ==== | ==== Hardware revision v1.0 ==== | ||
=== General/dimensions/weights === | === General/dimensions/weights === | ||
+ | {{anchor:td-general:}} | ||
|<75% 40% 60%>| | |<75% 40% 60%>| | ||
| Housing | aluminum-profile framework\\ acrylic glass\\ integrated LED lighting | | | Housing | aluminum-profile framework\\ acrylic glass\\ integrated LED lighting | | ||
Line 14: | Line 15: | ||
=== Temperatures === | === Temperatures === | ||
+ | {{anchor:td-temperatures:}} | ||
|<75% 40% 60%>| | |<75% 40% 60%>| | ||
| Extrusion temperature | max. +300°C | | | Extrusion temperature | max. +300°C | | ||
Line 21: | Line 23: | ||
=== Hot ends === | === Hot ends === | ||
+ | {{anchor:td-hot-ends:}} | ||
|<75% 40% 25% 35%>| | |<75% 40% 25% 35%>| | ||
| Screwable M6 brass nozzles A/F8 \\ (included in delivery) | Bore diameter\\ [mm] | Recommended layer height\\ First layer / following | | | Screwable M6 brass nozzles A/F8 \\ (included in delivery) | Bore diameter\\ [mm] | Recommended layer height\\ First layer / following | | ||
Line 31: | Line 34: | ||
=== Print === | === Print === | ||
+ | {{anchor:td-print:}} | ||
|<75% 40% 60%>| | |<75% 40% 60%>| | ||
| Print volume | 200x185x280mm (10.4 liter) | | | Print volume | 200x185x280mm (10.4 liter) | | ||
Line 36: | Line 40: | ||
| Print bed | exchangeable 210x210mm PEI/glass fabric/carbon composite sheet | | | Print bed | exchangeable 210x210mm PEI/glass fabric/carbon composite sheet | | ||
| Layer height | min. 0.1mm | | | Layer height | min. 0.1mm | | ||
- | | Reproduction accuracy | ±0.1mm | | + | | Positioning accuracy | ±0.1mm | |
- | | Tolerance | ±0.1mm | | + | | Tolerance | ±0.2mm | |
- | | Positioning step-width axes | X=0.028mm\\ Y=0.019mm\\ Z=0.003mm | | + | |
=== Material === | === Material === | ||
+ | {{anchor:td-material:}} | ||
|<75% 40% 60%>| | |<75% 40% 60%>| | ||
| Printable materials | ABS, PLA, HIPS, PVA, PC, PA12, PET | | | Printable materials | ABS, PLA, HIPS, PVA, PC, PA12, PET | | ||
Line 47: | Line 51: | ||
=== Power and Electronics === | === Power and Electronics === | ||
+ | {{anchor:td-electronics:}} | ||
|<75% 40% 60%>| | |<75% 40% 60%>| | ||
| Power consumption (total) | approx. 800W | | | Power consumption (total) | approx. 800W | | ||
Line 57: | Line 62: | ||
| Fans | 3x 119x119x25mm, 12V, 140m³/h axial fan (heat chamber circulation and cooling system)\\ 1x 80x80x25, 12V, 33m³/h axial fan (air filter) | | | Fans | 3x 119x119x25mm, 12V, 140m³/h axial fan (heat chamber circulation and cooling system)\\ 1x 80x80x25, 12V, 33m³/h axial fan (air filter) | | ||
| Network | Ethernet 10/100, RJ45 | | | Network | Ethernet 10/100, RJ45 | | ||
- | |||
- | |||
=== Sensors === | === Sensors === | ||
+ | {{anchor:td-sensors:}} | ||
|<75% 40% 60%>| | |<75% 40% 60%>| | ||
| Limit switch\\ H-frame (X/Y) and print table (Z) | magnetic hall endstops | | | Limit switch\\ H-frame (X/Y) and print table (Z) | magnetic hall endstops | | ||
Line 67: | Line 71: | ||
=== Closed loop water cooling system === | === Closed loop water cooling system === | ||
+ | {{anchor:td-cooling:}} | ||
|<75% 40% 60%>| | |<75% 40% 60%>| | ||
| Pump | 12V(DC) circulation pump with integrated compensation reservoir | | | Pump | 12V(DC) circulation pump with integrated compensation reservoir | | ||
Line 78: | Line 83: | ||
=== Air filter === | === Air filter === | ||
+ | {{anchor:td-air-filter:}} | ||
|<75% 40% 60%>| | |<75% 40% 60%>| | ||
| Air filter | fan duct with exchangeable activated charcoal container | | | Air filter | fan duct with exchangeable activated charcoal container | |