ht500:manual
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
ht500:manual [2016/04/25 13:30] Simon Kühling removed outdated paragraph |
ht500:manual [2016/05/25 08:16] Markus Bürgener [Hardware components] new graphic and structure |
||
|---|---|---|---|
| Line 35: | Line 35: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:typeplate_122015.png?400|Type plate on the rear side.}}] | + | [{{:ht500:type_plate_ht500.png?400|Type plate on the rear side.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 222: | Line 222: | ||
| === Noise === | === Noise === | ||
| - | The HT500 3D Printer is build to be operated in a professional environment such as workshops and laboratories. It is not suited for the operation in an office. The noise level may shortly reach peak values up to 73dB(A). During print jobs, it does not exceed 60dB(A), which is considered "unauspicious" for long-term exposure.\\ | + | The HT500 3D Printer is build to be operated in a professional environment such as workshops and laboratories. It is not suited for the operation in an office. During print jobs, it does not exceed 60dB(A), which is considered "unauspicious" for long-term exposure.\\ |
| Special noise protection equipment is not required. | Special noise protection equipment is not required. | ||
| Line 320: | Line 320: | ||
| | **R** | Right | Right side of the 3D Printer, referred to the frontal view. | | | **R** | Right | Right side of the 3D Printer, referred to the frontal view. | | ||
| | **B** | Back | Backside of the 3D Printer, referred to the frontal view | | | **B** | Back | Backside of the 3D Printer, referred to the frontal view | | ||
| - | </WRAP> | ||
| - | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_points_of_view.png?400|Directions and aspects of the 3D Printer. All statements refer to the frontal view.}}] | ||
| - | </WRAP> | ||
| - | </WRAP> | ||
| - | |||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP half column> | ||
| All movement directions of the axes are defined throughout this manual as follows: | All movement directions of the axes are defined throughout this manual as follows: | ||
| |<100% 5% 25% 70%>| | |<100% 5% 25% 70%>| | ||
| Line 339: | Line 330: | ||
| | **Z⊕** | Z positive | Print table moves down. | | | **Z⊕** | Z positive | Print table moves down. | | ||
| | **ZΘ** | Z negative | Print table moves up. | | | **ZΘ** | Z negative | Print table moves up. | | ||
| + | |||
| + | |||
| + | |||
| </WRAP> | </WRAP> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_moving_axes.png?400|Denotation and direction determination of the axes.}}] | + | [{{:ht500:directions_ht500.png?400|Directions and aspects of the 3D Printer. All statements refer to the frontal view.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| - | |||
| <WRAP group> | <WRAP group> | ||
| Line 564: | Line 557: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_filamentfeedunit.png?400|Filament supply}}] | + | [{{:ht500:desc_filamentfeedunit.png?400|Filament supply}}] |
| - | [{{:reprap-industrial-v1:desc_filamentfeedunit_dustsponge.png?400|Filament inlet with limit switch and dust wiping sponge.}}] | + | [{{:ht500:desc_filamentfeedunit_dustsponge.png?400|Filament inlet with limit switch and dust wiping sponge.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
ht500/manual.txt · Last modified: 2018/06/11 14:23 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
