ht500:quick-start-guide
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
ht500:quick-start-guide [2016/03/15 08:18] Markus Bürgener created |
ht500:quick-start-guide [2016/03/24 11:41] (current) Markus Bürgener [Safety precautions] |
||
|---|---|---|---|
| Line 16: | Line 16: | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{ :reprap-industrial-v1:qsg_overview_1.png?420 |The two main functional sections of the HT500 3D Printer: the build chamber with the functional components and the electronic chamber containing the regulation electronics.}}] | + | [{{ :ht500:qsg_overview_1.png?420 |The two main functional sections of the HT500 3D Printer: the build chamber with the functional components and the electronic chamber containing the regulation electronics.}}] |
| </WRAP> | </WRAP> | ||
| Line 40: | Line 40: | ||
| </WRAP> | </WRAP> | ||
| + | <WRAP pagebreak></WRAP> | ||
| <WRAP group> | <WRAP group> | ||
| Line 68: | Line 69: | ||
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| + | |||
| + | <WRAP pagebreak></WRAP> | ||
| ===== Safety precautions ===== | ===== Safety precautions ===== | ||
| Line 103: | Line 106: | ||
| NOTICE | NOTICE | ||
| - | In order to ensure your own safety and the proper functioning of your HT500 during operation read and observe the safety instructions in the online documentation. | + | If the 3D Printer has a temperature below 16°C (e.g. directly after delivery in cold weather) there is a danger of air humidity condensing on sensitive electronic components. This can lead to severe damages due to short circuiting during commissioning.\\ Therefore, it is necessary to thoroughly let the 3D Printer warm up to ambient temperature for at least 12 hrs. at its operating place **prior** to commissioning.\\ Regard the [[technical-data#td-ac|ambient conditions]] required for operation. |
| </WRAP> | </WRAP> | ||
| + | <WRAP note> | ||
| + | NOTICE | ||
| + | |||
| + | In order to ensure your own safety and the proper functioning of your HT500 during operation read and observe the safety instructions in the online documentation. | ||
| + | </WRAP> | ||
| ===== Installation requirements ===== | ===== Installation requirements ===== | ||
| <WRAP group> | <WRAP group> | ||
| Line 150: | Line 158: | ||
| <WRAP half column> | <WRAP half column> | ||
| * Switch to the **Setup** tab via the respective button in the header. | * Switch to the **Setup** tab via the respective button in the header. | ||
| - | * Write down the web-interface URL displayed on the right half of the screen. | + | * Write down the **Web Interface URL** displayed on the right half of the screen. |
| </WRAP> | </WRAP> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{ :reprap-industrial-v1:qsg_setupurl_fullscreen.png?400 |The web-interface URL on the SETUP screen is required for connecting the 3D Printer with your local network.}}] | + | [{{ :reprap-industrial-v1:qsg_setupurl_fullscreen.png?400 |The Web Interface URL on the SETUP screen is required for connecting the 3D Printer with your local network.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 160: | Line 168: | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | * Now open your web browser on your PC and enter the web-interface URL in the address line. You will be greeted with the **First steps** screen that provides a direct link to the online manual where all steps next to be taken are explained in detail.\\ \\ If you encounter problems with accessing the 3D Printer (or anything else) you may find help in the Troubleshooting section of the online manual\\ ([[http://docs.kuehlingkuehling.de/ht500/troubleshooting]]). | + | * Now open your web browser on your PC and enter the web interface URL in the address line and you will be greeted with the **First Steps** screen that provides a direct link to the online manual.\\ \\ All further steps are explained in in the Initial Commissioning chapter of the operating manual under [[http://docs.kuehlingkuehling.de/ht500/operation#initial-commissioning]]\\ \\ If you encounter problems with accessing the 3D Printer (or anything else) you may find help in the Troubleshooting section of the online manual\\ ([[http://docs.kuehlingkuehling.de/ht500/troubleshooting]]). |
| </WRAP> | </WRAP> | ||
ht500/quick-start-guide.1458029939.txt.gz · Last modified: 2016/03/15 08:18 by Markus Bürgener
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
