This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
reprap-industrial-v1:service-guide [2015/10/30 11:14] Markus Bürgener [Remedying clogging] restructured |
reprap-industrial-v1:service-guide [2015/11/02 07:59] Markus Bürgener [Replacing the heating block] |
||
---|---|---|---|
Line 335: | Line 335: | ||
* pipe cleaner | * pipe cleaner | ||
=== Additional information === | === Additional information === | ||
- | |<50% 80% 20%>| | + | [[{|width: 25em}#dissemblingre-installing-the-hot-end-nozzle-tips-andor-barrels|Disassembly / re-installation of nozzle and barrel]]\\ |
- | | Disassembly / re-installation of nozzle and barrel | [[{|width: 8em}#Dissembling / re-installing the hot end nozzle tips and/or barrels|Service guide]] | | + | [[{|width: 25em}reprap-industrial-v1:knowledge-base#materials|Suitable solvents]]\\ |
- | | Suitable solvents | [[{|width: 8em}reprap-industrial-v1:knowledge-base#materials|Knowledge base]] | | + | [[{|width: 25em}Software version v1.1.0 - Operation and commissioning#Changing the filament|Changing the filament]] | |
- | | Removing / reinserting filament | Software manual\\ [[{|width: 8em}Software version v1.0.5 - Operation and commissioning#Changing the filament|v1.0.5]]\\ [[{|width: 8em}Software version v1.1.0 - Operation and commissioning#Changing the filament|v1.1.0]] | | + | |
<WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
Line 429: | Line 428: | ||
=== Additional information === | === Additional information === | ||
- | * Software manual [[Software version v1.0.5 - Operation and commissioning#Manual Control|v1.0.5]] | + | [[{|width: 10em}software-version-v1.1.0-operation-and-commissioning#expert-control-screen|Software manual]] |
- | * Software manual [[Software version v1.1.0 - Operation and commissioning#Print|v1.1.0]] | + | |
=== Removing === | === Removing === | ||
Line 498: | Line 496: | ||
=== Additional information === | === Additional information === | ||
{{anchor:sg02}} | {{anchor:sg02}} | ||
- | * [[#Cleaning recommendation|]] | + | [[{|width: 15em}#Cleaning recommendation|Cleaning recommendation]]\\ |
- | * Software manual: [[reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc131|filament change]], [[reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc14t05|expert control]] | + | [[{|width: 15em}reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc131|Software manual - filament change]] [[{|width: 15em}reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc14t05|Software manual - expert control]] |
<WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
Line 687: | Line 685: | ||
* Allen wrench #1.5 | * Allen wrench #1.5 | ||
- | === Accompanying information === | + | === Additional information === |
- | * Troubleshooting: [[reprap-industrial-v1:troubleshooting#p9|P9]], [[reprap-industrial-v1:troubleshooting#em1|EM1]] | + | [[{|width: 10em}reprap-industrial-v1:troubleshooting#p9|Troubleshooting P9]]\\ |
+ | [[{|width: 10em}reprap-industrial-v1:troubleshooting#em1|Troubleshooting EM1]] | ||
=== Heating block exchange procedure === | === Heating block exchange procedure === |