reprap-industrial-v1:software-firmware-upgrades
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Last revision Both sides next revision | ||
|
reprap-industrial-v1:software-firmware-upgrades [2015/04/30 08:55] Simon Kühling [Preparing a new Micro-SD card] |
reprap-industrial-v1:software-firmware-upgrades [2015/04/30 08:57] Simon Kühling [Upgrade Instructions for Hardware Revision 1.0.0] changed instructions order |
||
|---|---|---|---|
| Line 53: | Line 53: | ||
| - First, [[#Preparing a new Micro-SD card|prepare a new Micro-SD card]]. | - First, [[#Preparing a new Micro-SD card|prepare a new Micro-SD card]]. | ||
| - [[reprap-industrial-v1:service-guide#exchanging-beaglebone-black-sd-card|Insert the SD card]] into the BeagleBone Black inside the electronics enclosure. | - [[reprap-industrial-v1:service-guide#exchanging-beaglebone-black-sd-card|Insert the SD card]] into the BeagleBone Black inside the electronics enclosure. | ||
| + | - If not running, power-up your RepRap Industrial. | ||
| + | - Verify all software components are running in the new versions as expected in the [[software-version-v1.1.0-operation-and-commissioning#setup|[Setup]]] tab from the touchscreen menu. | ||
| + | - Configure your Filament and Preheating Profiles in the [[software-version-v1.1.0-operation-and-commissioning#configuration|[Configuration]]] tab in the touchscreen menu. | ||
| - Go to the [[https://github.com/kuehlingkuehling/RepRap-Industrial-Slic3r-profiles/releases|RepRap Industrial Slic3r Profile Bundle Repository]] and download the latest profile bundle **that is compatible with your hardware revision and the new firmware version** (see compatibility notes for each profile bundle release). | - Go to the [[https://github.com/kuehlingkuehling/RepRap-Industrial-Slic3r-profiles/releases|RepRap Industrial Slic3r Profile Bundle Repository]] and download the latest profile bundle **that is compatible with your hardware revision and the new firmware version** (see compatibility notes for each profile bundle release). | ||
| - If necessary upgrade your [[http://slic3r.org|Slic3r]] installation to the version stated in the compatibility notes for the profile bundle you just downloaded. | - If necessary upgrade your [[http://slic3r.org|Slic3r]] installation to the version stated in the compatibility notes for the profile bundle you just downloaded. | ||
| Line 62: | Line 65: | ||
| </WRAP> | </WRAP> | ||
| - Install the new Slic3r Profile Bundle as described in the README file within your downloaded profile bundle archive. | - Install the new Slic3r Profile Bundle as described in the README file within your downloaded profile bundle archive. | ||
| - | - If not running, power-up your RepRap Industrial. | ||
| - | - Verify all software components are running in the new versions as expected in the [[software-version-v1.1.0-operation-and-commissioning#setup|[Setup]]] tab from the touchscreen menu. | ||
| - | - Configure your Filament and Preheating Profiles in the [[software-version-v1.1.0-operation-and-commissioning#configuration|[Configuration]]] tab in the touchscreen menu. | ||
| -- [[tips-tricks#changing-shell-password-in-the-beaglebone-black-operating-system|Change your System shell password]] via SSH. | -- [[tips-tricks#changing-shell-password-in-the-beaglebone-black-operating-system|Change your System shell password]] via SSH. | ||
| .. <WRAP note> | .. <WRAP note> | ||
reprap-industrial-v1/software-firmware-upgrades.txt · Last modified: 2015/04/30 08:58 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
