reprap-industrial-v1:tips-tricks
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
reprap-industrial-v1:tips-tricks [2015/09/17 08:45] Markus Bürgener [Deactivating the heating elements after end of print job] |
reprap-industrial-v1:tips-tricks [2015/11/17 12:37] Markus Bürgener removed |
||
|---|---|---|---|
| Line 28: | Line 28: | ||
| iface eth0 inet static | iface eth0 inet static | ||
| address 192.168.1.20 | address 192.168.1.20 | ||
| - | netmask 255.255.2555.0 | + | netmask 255.255.255.0 |
| - | network 192.468.1.0 | + | |
| broadcast 192.168.1.255 | broadcast 192.168.1.255 | ||
| - | gateway 192.168.1.254 | + | gateway 192.168.1.1 |
| dns-search family.local | dns-search family.local | ||
| - | dns-nameservers 192.168.1.254 | + | dns-nameservers 192.168.1.1 |
| pre-up iptables-restore </etc/iptables.rules | pre-up iptables-restore </etc/iptables.rules | ||
| Line 192: | Line 191: | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | Accurate leveling is vitally important for the print result. Although correct first layer settings can compensate for slight unevennesses of the print bed, false leveling will ruin a print within the first few layers. | + | Accurate leveling is vitally important for the print result. Although correct first layer settings can compensate for slight unevennesses of the print bed, false leveling will ruin a print within the first few layers. \\ |
| Evidence for a leveling mistake can be: | Evidence for a leveling mistake can be: | ||
| - | - Asymmetrical layer thickness, especially of the first layer, due to lopsided leveling. | + | ^ No. ^ Appearance ^ Reason ^ |
| - | * On one side of the print bed the extruded strand is laid on the print bed instead of being spread → the print bed and the nozzle are too far apart. | + | | 1 | Asymmetrical layer thickness, especially of the first layer. | lopsided leveling\\ Appearance 2 and 3 are visible simultaneously | |
| - | * On the other side of the print bed the extruded strand is pressed onto the print bed until the nozzle tip is clogged → the print bed and the nozzle are too close. | + | | 2 | Smearing of the extrusion and possibly clogging of the nozzle. | Print bed and the nozzle are too close together. | |
| - | - Smearing of the extrusion and possibly clogging of the nozzle due to too closely leveled bed. | + | | 3 | The extruded strand is laid on the print bed instead of being spread. | Print bed and the nozzle are too far apart.\\ (can be due to a wrong bed temperature also – better double-check) | |
| - | - Strands do not stick to the print bed but are being pulled away by the nozzle tip. Of course, this can be due to a wrong bed temperature also – better double-check. | + | |::: | Strands do not stick to the print bed but are being pulled away by the nozzle tip. |::: | |
| - | - Extrusion of rounded, unjoined strands. | + | | 4 | Extrusion of rounded, unjoined strands. | Print bed and the nozzle are too far apart. | |
| - | </WRAP> | + | |
| + | </WRAP> | ||
| <WRAP half column> | <WRAP half column> | ||
| [{{:reprap-industrial-v1:lopsidedleveling.png?400|Leveling mistakes: examples of characteristic appearances of the first layer.}}] | [{{:reprap-industrial-v1:lopsidedleveling.png?400|Leveling mistakes: examples of characteristic appearances of the first layer.}}] | ||
| Line 382: | Line 381: | ||
| - Open your slicing software. | - Open your slicing software. | ||
| - Open the tab [Printer Settings]. | - Open the tab [Printer Settings]. | ||
| - | - Choose the //Start G-code// in the "Custom G-code" menu. | + | - Choose the //Start G-code// editor in the "Custom G-code" menu. |
| -- Scroll down to\\ ''; PREHEAT BED AND CHAMBER''\\ and position the cursor in the line reading:\\ <code> M104 S70 T2; set recirculating air heater to 70 degree celcius target temperature</code> | -- Scroll down to\\ ''; PREHEAT BED AND CHAMBER''\\ and position the cursor in the line reading:\\ <code> M104 S70 T2; set recirculating air heater to 70 degree celcius target temperature</code> | ||
| - Change the entry "S//xy//" (here //S70//) by replacing the value //xy// with the desired temperature, for example //50° C//:\\ <code>M104 S50 T2; set recirculating air heater to 50 degree celcius target temperature</code> (for logical reasons, the comment should be aligned). | - Change the entry "S//xy//" (here //S70//) by replacing the value //xy// with the desired temperature, for example //50° C//:\\ <code>M104 S50 T2; set recirculating air heater to 50 degree celcius target temperature</code> (for logical reasons, the comment should be aligned). | ||
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
