reprap-industrial-v1:troubleshooting
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
reprap-industrial-v1:troubleshooting [2015/11/02 08:51] Markus Bürgener [Printing process / print quality] |
reprap-industrial-v1:troubleshooting [2015/11/02 09:00] Markus Bürgener [Mechanical] |
||
|---|---|---|---|
| Line 53: | Line 53: | ||
| |< 100% 4% 25% 27% 27% 17% >| | |< 100% 4% 25% 27% 27% 17% >| | ||
| ^ No. ^ Symptom ^ Possible cause(s) ^ To do ^ Additional information ^ | ^ No. ^ Symptom ^ Possible cause(s) ^ To do ^ Additional information ^ | ||
| - | | {{anchor:m1:M1}} | Juddering of the print table during homing. | Very dry shafts lead to increased stick-and-slip effects. | ✔ Lubricate the Z-shafts with //Ballistol Universal// \\ <WRAP note> NOTICE\\ //Only valid for\\ RepRap Industrial 3D printers up to\\ hardware revision 1.1.0.// </WRAP> | [[reprap-industrial-v1:service-guide#shaft-lubrication|Service guide]] | | + | | {{anchor:m1:M1}} | Juddering of the print table during homing. | Very dry shafts lead to increased stick-and-slip effects. | ✔ Lubricate the Z-shafts with //Ballistol Universal// \\ <WRAP note> NOTICE\\ //Only valid for\\ RepRap Industrial 3D printers up to\\ hardware revision 1.1.0.// </WRAP> | [[{|width:10em}reprap-industrial-v1:service-guide#shaft-lubrication|Service guide]] | |
| - | | {{anchor:m2:M2}} | Increasingly rough vertical surfaces | Very dry shafts may lead to increased vibrations of the extruder. | ✔ Lubricate the X- and Y-shafts with //Ballistol Universal// \\ <WRAP note> NOTICE\\ //Only valid for\\ RepRap Industrial 3D printers up to\\ hardware revision 1.1.0.// </WRAP> | [[reprap-industrial-v1:service-guide#shaft-lubrication|Service guide]] | | + | | {{anchor:m2:M2}} | Increasingly rough vertical surfaces | Very dry shafts may lead to increased vibrations of the extruder. | ✔ Lubricate the X- and Y-shafts with //Ballistol Universal// \\ <WRAP note> NOTICE\\ //Only valid for\\ RepRap Industrial 3D printers up to\\ hardware revision 1.1.0.// </WRAP> | [[{|width:10em}reprap-industrial-v1:service-guide#shaft-lubrication|Service guide]] | |
| | {{anchor:m3:M3}} | Homing the X-axis leads to extruder head collision and blackout of the controls. | X-axis limit stop bent by crash due to misinterpreted home-position. | ✔ Disconnect the printer from the power supply and carefully bend back limit stop with tweezers.\\ <WRAP note>**NOTICE**\\ Always power down the 3D printer before touching electronic components with conductive tools to avoid damages by short-circuiting.</WRAP> | | | | {{anchor:m3:M3}} | Homing the X-axis leads to extruder head collision and blackout of the controls. | X-axis limit stop bent by crash due to misinterpreted home-position. | ✔ Disconnect the printer from the power supply and carefully bend back limit stop with tweezers.\\ <WRAP note>**NOTICE**\\ Always power down the 3D printer before touching electronic components with conductive tools to avoid damages by short-circuiting.</WRAP> | | | ||
| - | |::: |::: | G-code home positions of X-axis incorrect. | ✔ Check Slic3r for correct axes settings\\ (depending on the release versions of the 3D printer version and the slic3r software). | [[reprap-industrial-v1:service-guide#print-bed-size-settings-for-different-hardware-and-slic3r-versions|Service guide]] | | + | |::: |::: | G-code home positions of X-axis incorrect. | ✔ Check Slic3r for correct axes settings\\ (depending on the release versions of the 3D printer version and the slic3r software). | [[{|width:10em}reprap-industrial-v1:service-guide#print-bed-size-settings-for-different-hardware-and-slic3r-versions|Service guide]] | |
| - | | {{anchor:m4:M4}} | Although the left extruder has been selected as reference during leveling, the print head moves the right extruder into the center position. | Extruder offset in the web interface has been set incorrect or for the false extruder (e.g. after an update). | ✔ Check in the //Setup// tab of the web-interface for the following:\\ Extr.1 X-offset [steps] set to ''0''\\ Extr.1 Y-offset [steps] set to ''0''\\ Extr.2 X-offset [steps] set to ''2078''\\ Extr.2 Y-offset [steps] set to ''-21''\\ \\ Regard that these are factory presets. Run the [Extruder Offset Calibration] wizard to adjust these for your specific 3D printer. | [[reprap-industrial-v1:software-firmware-upgrades#upgrade-instructions-for-hardware-revision-110|Upgrade information]] | | + | | {{anchor:m4:M4}} | Although the left extruder has been selected as reference during leveling, the print head moves the right extruder into the center position. | Extruder offset in the web interface has been set incorrect or for the false extruder (e.g. after an update). | ✔ Check in the //Setup// tab of the web-interface for the following:\\ Extr.1 X-offset [steps] set to ''0''\\ Extr.1 Y-offset [steps] set to ''0''\\ Extr.2 X-offset [steps] set to ''2078''\\ Extr.2 Y-offset [steps] set to ''-21''\\ \\ Regard that these are factory presets. Run the [Extruder Offset Calibration] wizard to adjust these for your specific 3D printer. | [[{|width:10em}reprap-industrial-v1:software-firmware-upgrades#upgrade-instructions-for-hardware-revision-110|Upgrade information]] | |
| - | | {{anchor:m5:M5}} | Filament uncoils from the spool\\ (especially when using new 2.3 kg spools). | The spool rim is too narrow for the amount of material on new spools. The material's elasticity is due to the manufacturing process and will cause the filament to uncoil when not under tension. | ✔ Print three to four of the //filament spool wings// provided at the GitHub repository and fasten them to the outside of the spool's rim. If required, apply a small amount of hot glue. | [[https://github.com/kuehlingkuehling/Tools-Accessories/tree/master/Filament%20Spool%20Wings|GitHub repository]]\\ {{ :reprap-industrial-v1:tools_spoolwings.jpg?100 |}} | | + | | {{anchor:m5:M5}} | Filament uncoils from the spool\\ (especially when using new 2.3 kg spools). | The spool rim is too narrow for the amount of material on new spools. The material's elasticity is due to the manufacturing process and will cause the filament to uncoil when not under tension. | ✔ Print three to four of the //filament spool wings// provided at the GitHub repository and fasten them to the outside of the spool's rim. If required, apply a small amount of hot glue. | [[{|width:10em;color:green}https://github.com/kuehlingkuehling/Tools-Accessories/tree/master/Filament%20Spool%20Wings|GitHub]]\\ {{ :reprap-industrial-v1:tools_spoolwings.jpg?100 |}} | |
| - | | {{anchor:m6:M6}} | Noticeable amount of gas bubbles in the cooling system. | Lack of coolant due to leakage. | ✔ Refill coolant. | [[reprap-industrial-v1:service-guide#cooling-water-pump|Service guide]] | | + | | {{anchor:m6:M6}} | Noticeable amount of gas bubbles in the cooling system. | Lack of coolant due to leakage. | ✔ Refill coolant. | [[{|width:10em}reprap-industrial-v1:service-guide#cooling-water-pump|Service guide]] | |
| ==== Electronic, network, communication ==== | ==== Electronic, network, communication ==== | ||
| |< 100% 4% 25% 27% 27% 17% >| | |< 100% 4% 25% 27% 27% 17% >| | ||
reprap-industrial-v1/troubleshooting.txt · Last modified: 2017/01/18 09:52 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
