reprap-industrial-v1:troubleshooting
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
reprap-industrial-v1:troubleshooting [2015/11/02 09:02] Markus Bürgener [Electronic, network, communication] |
reprap-industrial-v1:troubleshooting [2015/11/02 09:04] Markus Bürgener [Error messages] |
||
|---|---|---|---|
| Line 78: | Line 78: | ||
| |< 100% 4% 25% 27% 27% 17% >| | |< 100% 4% 25% 27% 27% 17% >| | ||
| ^ No. ^ Symptom ^ Possible cause(s) ^ To do ^ Additional information ^ | ^ No. ^ Symptom ^ Possible cause(s) ^ To do ^ Additional information ^ | ||
| - | | {{anchor:s1:S1}} | Profile names are not readable in Slic3r drop-down menus. | Incompatibility of Slic3r (v1.1.7) and Windows operating software. | ✔ Rename profiles with shorter description.\\ ✔ Upgrade to higher version of Slic3r. | [[reprap-industrial-v1:tips-tricks#Profile display problems in Slic3r for Windows|Tips&Tricks]],\\ [[http://slic3r.org/download|Slic3r]] | | + | | {{anchor:s1:S1}} | Profile names are not readable in Slic3r drop-down menus. | Incompatibility of Slic3r (v1.1.7) and Windows operating software. | ✔ Rename profiles with shorter description.\\ ✔ Upgrade to higher version of Slic3r. | [[{|width:10em}reprap-industrial-v1:tips-tricks#Profile display problems in Slic3r for Windows|Tips&Tricks]]\\ [[{|width:10em;color:green}http://slic3r.org/download|Slic3r]] | |
| - | | {{anchor:s2:S2}} | Crashing of Slic3r with STL-file. | STL-file corrupted\\ see [[#P8]] also | ✔ Check the STL-file for holes, intersections, misaligned edges and the like. Repair or redesign if necessary. | [[reprap-industrial-v1:tips-tricks#suitability-check-of-.stl-data|Tips&Tricks]] | | + | | {{anchor:s2:S2}} | Crashing of Slic3r with STL-file. | STL-file corrupted\\ see [[#P8]] also | ✔ Check the STL-file for holes, intersections, misaligned edges and the like. Repair or redesign if necessary. | [[{|width:10em}reprap-industrial-v1:tips-tricks#suitability-check-of-.stl-data|Tips&Tricks]] | |
| Line 88: | Line 88: | ||
| Use the below list if an ERROR message appears in your log file and you are unsure about its meaning and effects. | Use the below list if an ERROR message appears in your log file and you are unsure about its meaning and effects. | ||
| ^ No. ^ Message ^ Possible cause(s)/\\ effects ^ To do ^ Further information ^ | ^ No. ^ Message ^ Possible cause(s)/\\ effects ^ To do ^ Further information ^ | ||
| - | | {{anchor:em1:EM1}} | ''Printer set into dry run mode until restart!''\\ <wrap lo>followed by internal test (example):\\ //extruder 0: temp sensor defect//\\ //extruder 1: working//\\ //extruder 2: working//\\ //heated bed: working//</wrap> | The named thermistor measured a limit value derivation. The measured temperature exceeded/came below the allowable limit value.\\ \\ All heating elements are switched off. Extrusion may stop mid-print. | ✔ Check cable connections of the thermistors for damage or wear.\\ If the fragile cables of the thermistor are broken, the heating unit must be replaced.\\ see [[#p9|P9]] also | Limit values are:\\ 0 … 300 °C\\ [[reprap-industrial-v1:service-guide#dissemblingre-installing-the-hot-end-nozzle-tips-andor-barrels|Service guide]]\\ \\ Request a quote for the fully assembled replacement part via [[sales@kuehlingkuehling.de]] | | + | | {{anchor:em1:EM1}} | ''Printer set into dry run mode until restart!''\\ <wrap lo>followed by internal test (example):\\ //extruder 0: temp sensor defect//\\ //extruder 1: working//\\ //extruder 2: working//\\ //heated bed: working//</wrap> | The named thermistor measured a limit value derivation. The measured temperature exceeded/came below the allowable limit value.\\ \\ All heating elements are switched off. Extrusion may stop mid-print. | ✔ Check cable connections of the thermistors for damage or wear.\\ If the fragile cables of the thermistor are broken, the heating unit must be replaced.\\ see [[#p9|P9]] also | Limit values are:\\ 0 … 300 °C\\ [[{|width:10em}reprap-industrial-v1:service-guide#dissemblingre-installing-the-hot-end-nozzle-tips-andor-barrels|Service guide]]\\ \\ Request a quote for the fully assembled replacement part via [[sales@kuehlingkuehling.de]] | |
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
reprap-industrial-v1/troubleshooting.txt · Last modified: 2017/01/18 09:52 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
