This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
reprap-industrial-v1:software-version-v1.0.5-operation-and-commissioning [2014/11/03 14:21] Markus Bürgener [Setup] links updated |
reprap-industrial-v1:software-version-v1.0.5-operation-and-commissioning [2014/11/03 15:04] Markus Bürgener [The first print] links updated/deleted |
||
---|---|---|---|
Line 21: | Line 21: | ||
|::: |::: | **//[[#Setup]]//** provides wizards for different preset operating procedures | | |::: |::: | **//[[#Setup]]//** provides wizards for different preset operating procedures | | ||
| 3 | Print job list | list of uploaded print jobs sorted by time/date (oldest first) | | | 3 | Print job list | list of uploaded print jobs sorted by time/date (oldest first) | | ||
- | | 4 | [Emergency STOP] button | see [[#Personnel safety and device reliability|safety information]] | | + | | 4 | [Emergency STOP] button | see [[manual#Emergency stop|safety information]] | |
| 5 | [print] button | Push to start the respective print job. | | | 5 | [print] button | Push to start the respective print job. | | ||
| 6 | Browse buttons | Use [Previous], [Next] and [//page number//] to browse the print job list. | | | 6 | Browse buttons | Use [Previous], [Next] and [//page number//] to browse the print job list. | | ||
Line 314: | Line 314: | ||
===== Initial commissioning ===== | ===== Initial commissioning ===== | ||
- | After [[:reprap-industrial-v1:manual|installation]] the RepRap Industrial is ready for initial commissioning. The first few steps will prepare your RepRap Industrial for its day-to-day duty: | + | After [[manual#Setup and Installation|installation]] the RepRap Industrial is ready for initial commissioning. The first few steps will prepare your RepRap Industrial for its day-to-day duty: |
* Make sure that no foreign objects are left in the build chamber (transport locks, tools or the like). | * Make sure that no foreign objects are left in the build chamber (transport locks, tools or the like). | ||
* Close the build chamber. | * Close the build chamber. | ||
Line 320: | Line 320: | ||
The next step is preheating the build chamber and the print bed in order to enable calibration at operating temperature: | The next step is preheating the build chamber and the print bed in order to enable calibration at operating temperature: | ||
* Tap [[#Manual Control|[Manual Control]]] to enter the respective menu. | * Tap [[#Manual Control|[Manual Control]]] to enter the respective menu. | ||
- | * Activate the build chamber by tapping [[#Queue|[Build Chamber ON]] and then start the heating by tapping [[#Manual Control|[Preheat Chamber/Bed ON]]]. The current temperatures are indicated on the right side of the screen. You can always check the temperature by tapping [[#Manual Control|[Refresh temperatures]]]. | + | * Activate the build chamber by tapping [[#Manual Control|[Build Chamber ON]]] and then start the heating by tapping [[#Manual Control|[Preheat Chamber/Bed ON]]]. The current temperatures are indicated on the right side of the screen. You can always check the temperature by tapping [[#Manual Control|[Refresh temperatures]]]. |
* Let the build chamber heat for approximately 45 minutes. | * Let the build chamber heat for approximately 45 minutes. | ||
Line 458: | Line 458: | ||
<WRAP group> | <WRAP group> | ||
<WRAP half column> | <WRAP half column> | ||
- | Make sure that all steps described in //[[#First start-up]]// have been carried out. | + | Make sure that all previously described steps have been carried out. |
The next steps are carried out at the 3D printer's GUI:\\ | The next steps are carried out at the 3D printer's GUI:\\ |