reprap-industrial-v1:software-version-v1.0.5-operation-and-commissioning
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
reprap-industrial-v1:software-version-v1.0.5-operation-and-commissioning [2014/11/03 14:39] Markus Bürgener [Queue] orthography |
reprap-industrial-v1:software-version-v1.0.5-operation-and-commissioning [2014/11/03 15:05] Markus Bürgener [Initial commissioning] |
||
|---|---|---|---|
| Line 314: | Line 314: | ||
| ===== Initial commissioning ===== | ===== Initial commissioning ===== | ||
| - | After [[:reprap-industrial-v1:manual|installation]] the RepRap Industrial is ready for initial commissioning. The first few steps will prepare your RepRap Industrial for its day-to-day duty: | + | After [[manual#Setup and Installation|installation]] the RepRap Industrial is ready for initial commissioning. The first few steps will prepare your RepRap Industrial for its day-to-day duty: |
| * Make sure that no foreign objects are left in the build chamber (transport locks, tools or the like). | * Make sure that no foreign objects are left in the build chamber (transport locks, tools or the like). | ||
| * Close the build chamber. | * Close the build chamber. | ||
| Line 320: | Line 320: | ||
| The next step is preheating the build chamber and the print bed in order to enable calibration at operating temperature: | The next step is preheating the build chamber and the print bed in order to enable calibration at operating temperature: | ||
| * Tap [[#Manual Control|[Manual Control]]] to enter the respective menu. | * Tap [[#Manual Control|[Manual Control]]] to enter the respective menu. | ||
| - | * Activate the build chamber by tapping [[#Queue|[Build Chamber ON]] and then start the heating by tapping [[#Manual Control|[Preheat Chamber/Bed ON]]]. The current temperatures are indicated on the right side of the screen. You can always check the temperature by tapping [[#Manual Control|[Refresh temperatures]]]. | + | * Activate the build chamber by tapping [[#Manual Control|[Build Chamber ON]]] and then start the heating by tapping [[#Manual Control|[Preheat Chamber/Bed ON]]]. The current temperatures are indicated on the right side of the screen. You can always check the temperature by tapping [[#Manual Control|[Refresh temperatures]]]. |
| * Let the build chamber heat for approximately 45 minutes. | * Let the build chamber heat for approximately 45 minutes. | ||
| Line 351: | Line 351: | ||
| To check or alter the settings, proceed as follows: | To check or alter the settings, proceed as follows: | ||
| - | The material profile for each extruder is chosen via the [Select Filament Profile] button in the **//Setup//** menu. | + | The material profile for each extruder is chosen via the [Select Filament Profile] button in the //Setup// menu. |
| </WRAP> | </WRAP> | ||
| Line 458: | Line 458: | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column> | <WRAP half column> | ||
| - | Make sure that all steps described in //[[#First start-up]]// have been carried out. | + | Make sure that all previously described steps have been carried out. |
| The next steps are carried out at the 3D printer's GUI:\\ | The next steps are carried out at the 3D printer's GUI:\\ | ||
reprap-industrial-v1/software-version-v1.0.5-operation-and-commissioning.txt · Last modified: 2015/03/13 10:06 by Markus Bürgener
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
