ht500-2:manual
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
ht500-2:manual [2017/02/23 08:46] Simon Kühling created |
ht500-2:manual [2017/02/28 13:51] (current) Simon Kühling image path fixes |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== HT500.2 - Manual ====== | ====== HT500.2 - Manual ====== | ||
| - | [{{:HT500.2_freigestellt.jpg?600|The Kühling&Kühling HT500.2 3D Printer}}] | + | [{{ht500-2_cover-image.png?600|The Kühling&Kühling HT500.2 3D Printer}}] |
| ====== General ====== | ====== General ====== | ||
| Line 35: | Line 35: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{type_plate_HT500-2.png?400|Type plate on the rear side.}}] | + | [{{nameplate-example.png?400|Type plate on the rear side.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 45: | Line 45: | ||
| ===== Intended use ===== | ===== Intended use ===== | ||
| The HT500.2 3D Printer has been designed and built for printing three-dimensional workpieces of nearly random geometries from common 2.85 mm thermoplastic filament strands.\\ The 3D Printer features advanced hot-ends with an extrusion temperature up to 500°C. In combination with the heated build chamber (up to 70°C) and the heated print bed (up to 130°C), this makes the HT500.2 suitable for printing a vast scope of materials. It is therefor capable of performing regular 3D printing tasks with standard thermoplastics as well as special jobs with a variety of technical plastics.\\ | The HT500.2 3D Printer has been designed and built for printing three-dimensional workpieces of nearly random geometries from common 2.85 mm thermoplastic filament strands.\\ The 3D Printer features advanced hot-ends with an extrusion temperature up to 500°C. In combination with the heated build chamber (up to 70°C) and the heated print bed (up to 130°C), this makes the HT500.2 suitable for printing a vast scope of materials. It is therefor capable of performing regular 3D printing tasks with standard thermoplastics as well as special jobs with a variety of technical plastics.\\ | ||
| - | [[http://kuehlingkuehling.de/imprint/|Contact]] //Kühling&Kühling// or refer to [[http://kuehlingkuehling.de/product-category/consumables/|our web shop]] for more detailed information on available and applicable materials. | + | [[http://kuehlingkuehling.de/imprint/|Contact]] //Kühling&Kühling// or refer to [[http://kuehlingkuehling.de|our website]] for more detailed information on available and applicable materials. |
| The HT500.2 is intended for industrial and commercial use. It is not valid for the operation in an explosive atmosphere.\\ | The HT500.2 is intended for industrial and commercial use. It is not valid for the operation in an explosive atmosphere.\\ | ||
| Line 222: | Line 222: | ||
| === Noise === | === Noise === | ||
| - | The HT500.2 3D Printer is build to be operated in a professional environment such as workshops and laboratories. It is not suited for the operation in an office. During print jobs, it does not exceed 60dB(A), which is considered "unauspicious" for long-term exposure.\\ | + | The HT500.2 3D Printer is build to be operated in a professional environment such as workshops and laboratories. It is not suited for the operation in an office. During print jobs, it does not exceed 60dB(A), which is considered "inauspicious" for long-term exposure.\\ |
| Special noise protection equipment is not required. | Special noise protection equipment is not required. | ||
| Line 245: | Line 245: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{gui_v110_emergencystop.png?400|The emergency stop button in the top-right corner of the GUI will immediately stop all movement and set the 3D Printer in a safe state for troubleshooting.}}] | + | [{{gui_emergencystop.png?400|The emergency stop button in the top-right corner of the GUI will immediately stop all movement and set the 3D Printer in a safe state for troubleshooting.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 336: | Line 336: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{directions_HT500-2.png?400|Directions and aspects of the 3D Printer. All statements refer to the frontal view.}}] | + | [{{directions_HT500.png?400|Directions and aspects of the 3D Printer. All statements refer to the frontal view.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 350: | Line 350: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_moving_drives.png?400|Movement directions of the extruder drives.}}] | + | [{{desc_moving_drives.png?400|Movement directions of the extruder drives.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 372: | Line 372: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_buildchamber_insideview.png?400|Inside view of the build chamber.}}] | + | [{{desc_buildchamber_insideview.png?400|Inside view of the build chamber.}}] |
| </WRAP> | </WRAP> | ||
| Line 387: | Line 387: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_buildchamber_backview.png?400|Filament supply unit at the rear side of the build chamber.}}] | + | [{{desc_buildchamber_backview.png?400|Filament supply unit at the rear side of the build chamber.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 417: | Line 417: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_extruderhead.png?400|Extruder head components}}] | + | [{{desc_extruderhead.png?400|Extruder head components}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 436: | Line 436: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{desc_extruderheadcomponents_HT500-2.png?400|Extruder head components}}] | + | [{{desc_extruderheadcomponents_HT500.png?400|Extruder head components}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 446: | Line 446: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_nozzletipsann.png?400|Markings to distinguish nozzle sizes.}}] | + | [{{desc_nozzletipsann.png?400|Markings to distinguish nozzle sizes.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 468: | Line 468: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:print_table_overview.png?400|Print table and print bed fastened with four bulldog clamps}}] | + | [{{print_table_overview.png?400|Print table and print bed fastened with four bulldog clamps}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 484: | Line 484: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:print_table_overview_2.png?400|3-point leveling support}}] | + | [{{print_table_overview_2.png?400|3-point leveling support}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 511: | Line 511: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_drives_2.png?400|Single views of the drive motors.}}] | + | [{{desc_drives_2.png?400|Single views of the drive motors.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 591: | Line 591: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_wiper.png?400|The wiper makes sure that the nozzle tip is always clean and well filled after a tool change during dual-material print jobs.}}] | + | [{{desc_wiper.png?400|The wiper makes sure that the nozzle tip is always clean and well filled after a tool change during dual-material print jobs.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 643: | Line 643: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{desc_HT500-2_overviewelectronicchamberright.png?400|Inside view of the electronic chamber (right side).}}] | + | [{{desc_HT500_overviewelectronicchamberright.png?400|Inside view of the electronic chamber (right side).}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 666: | Line 666: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:desc_overviewelectronicchamberhind_typeplate.png?400|Rear cover}}] | + | [{{desc_overviewelectronicchamberhind_typeplate.png?400|Rear cover}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 684: | Line 684: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{desc_HT500-2_electronicchamberfront.png?400|Touchscreen user interface and wake button at the front cover.}}] | + | [{{desc_HT500_electronicchamberfront.png?400|Touchscreen user interface and wake button at the front cover.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 700: | Line 700: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:touchscreen.png?400|The high-resolution 10"-TFT touchscreen mounted at the front panel enables direct operation of the HT500.2.}}] | + | [{{touchscreen.png?400|The high-resolution 10"-TFT touchscreen mounted at the front panel enables direct operation of the HT500.2.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 710: | Line 710: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:gui_setupmenu_v110_rrorversion.png?400|RepRapOnRails software version displayed in the //Setup// menu.}}] | + | [{{gui_setupmenu_v110_rrorversion.png?400|RepRapOnRails software version displayed in the //Setup// menu.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| Line 774: | Line 774: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:secure_boxed.png?400|The wooden box and the lid are fastened to the pallet with tensioning straps.\\ The 3D Printer is padded with air cushion foil and a wooden cover plate and strapped to the pallet with tensioning straps.}}] | + | [{{secure_boxed.png?400|The wooden box and the lid are fastened to the pallet with tensioning straps.\\ The 3D Printer is padded with air cushion foil and a wooden cover plate and strapped to the pallet with tensioning straps.}}] |
| <WRAP info> | <WRAP info> | ||
| INFO | INFO | ||
| Line 793: | Line 793: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{:reprap-industrial-v1:secure_yaxis.png?400|Transport restraint of the Y-axis: blue tape spans from the hind Y-shaft to the left Z-shaft and from the front Y-shaft to the top cover.}}]\\ | + | [{{secure_yaxis.png?400|Transport restraint of the Y-axis: blue tape spans from the hind Y-shaft to the left Z-shaft and from the front Y-shaft to the top cover.}}]\\ |
| - | [{{:reprap-industrial-v1:secure_headchain.png?400|Transport restraint of the main e-chain: blue tape is strapped around the chain an fastened to the top cover.\\ Transport restraint of the extruder head: the extruder head is cushioned with air cushion foil and strapped to the right X-end with blue tape.}}]\\ | + | [{{secure_headchain.png?400|Transport restraint of the main e-chain: blue tape is strapped around the chain an fastened to the top cover.\\ Transport restraint of the extruder head: the extruder head is cushioned with air cushion foil and strapped to the right X-end with blue tape.}}]\\ |
| - | [{{:reprap-industrial-v1:secure_doors.png?400|The doors are held close by blue tape at the top and lower edge.\\ The touchscreen is packed in air cushion foil.}}]\\ | + | [{{secure_doors.png?400|The doors are held close by blue tape at the top and lower edge.\\ The touchscreen is packed in air cushion foil.}}]\\ |
| - | [{{:reprap-industrial-v1:secure_table.png?400|A cardboard frame supports the print table.}}] | + | [{{secure_table.png?400|A cardboard frame supports the print table.}}] |
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
ht500-2/manual.1487839574.txt.gz · Last modified: 2017/02/23 08:46 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
