ht500:technical-data
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
ht500:technical-data [2016/03/15 16:18] Simon Kühling |
ht500:technical-data [2017/06/09 12:20] (current) Simon Kühling [Hardware revision v1.4.x] remove experimental materials |
||
|---|---|---|---|
| Line 36: | Line 36: | ||
| | Print bed | exchangeable 210x210mm PEI/glass fabric/carbon composite sheet | | | Print bed | exchangeable 210x210mm PEI/glass fabric/carbon composite sheet | | ||
| | Minimum layer resolution | 0.1mm | | | Minimum layer resolution | 0.1mm | | ||
| - | | Reproduction accuracy | ±0.1mm | | + | | Positioning accuracy | ±0.1mm | |
| - | | Tolerance | ±0.1mm | | + | | Approx. Tolerance | ±0.2mm | |
| === Material === | === Material === | ||
| |<75% 40% 60%>| | |<75% 40% 60%>| | ||
| - | | Printable materials | ABS, PLA, HIPS, PVA, PC, PA12, PET, PEEK, PP, POM | | + | | Printable materials | ABS, PLA, HIPS, PVA, PC, PA12, PET | |
| | Filament diameter | 2.85±0.1mm | | | Filament diameter | 2.85±0.1mm | | ||
| | Available filament qty. | 0.75kg spool (200x55mm)\\ 2.30kg spool (296x100mm) | | | Available filament qty. | 0.75kg spool (200x55mm)\\ 2.30kg spool (296x100mm) | | ||
| Line 53: | Line 53: | ||
| |::: | 2x 1.2A planetary gear drive stepper motor (extruder drives) | | |::: | 2x 1.2A planetary gear drive stepper motor (extruder drives) | | ||
| | Positioning step-width axes | X=0.028mm\\ Y=0.019mm\\ Z=0.003mm | | | Positioning step-width axes | X=0.028mm\\ Y=0.019mm\\ Z=0.003mm | | ||
| - | | Hot ends | 12V, 24W ceramic heating cartridge per hot end | | + | | Hot ends | 12V, 40W integrated heating element per hot end | |
| | Print bed heating | 170W wired silicone heating pad | | | Print bed heating | 170W wired silicone heating pad | | ||
| | Chamber heating | 4x 170W heating resistor (two per heating element) | | | Chamber heating | 4x 170W heating resistor (two per heating element) | | ||
| | Chamber lighting | 2x 4W LED array, 6.500K | | | Chamber lighting | 2x 4W LED array, 6.500K | | ||
| | Stand-alone operating module | integrated capacitive 10” touchscreen controller | | | Stand-alone operating module | integrated capacitive 10” touchscreen controller | | ||
| - | | Integrated computer | BeagleBone Black | | + | | Integrated computer | UDOO Quad Single Board Computer (Quad core 1GHz CPU) | |
| - | | Machine control | RUMBA microprocessor board | | + | | Machine control | RADDS v1.5 3D Printer Driver Shield | |
| - | | Load switching | 5x 15A MOSFET board | | + | | Load switching | 3x High Current Solid State Relais | |
| | Fans | 3x 119x119x25mm, 12V, 140m³/h axial fan\\ (heat chamber circulation and cooling system) | | | Fans | 3x 119x119x25mm, 12V, 140m³/h axial fan\\ (heat chamber circulation and cooling system) | | ||
| |::: | 1x 80x80x25, 12V, 33m³/h axial fan (air filter) | | |::: | 1x 80x80x25, 12V, 33m³/h axial fan (air filter) | | ||
ht500/technical-data.1458058722.txt.gz · Last modified: 2016/03/15 16:18 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
