reprap-industrial-v1:knowledge-base
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
reprap-industrial-v1:knowledge-base [2015/11/17 14:56] Markus Bürgener [Setting a static IP address for RepRap Industrial ethernet connection] links updated |
reprap-industrial-v1:knowledge-base [2016/01/25 13:17] Markus Bürgener [Polylactic Acid (PLA)] |
||
|---|---|---|---|
| Line 1145: | Line 1145: | ||
| |<100% 25% 55% 20%>| | |<100% 25% 55% 20%>| | ||
| ^ Feature ^ Setting ^ see also ^ | ^ Feature ^ Setting ^ see also ^ | ||
| - | | Print bed design | standard PEI print bed, glass | | | + | | Print bed design | standard PEI print bed, glass, [[http://www.buildtak.eu/shop/|BuildTak]] | | |
| - | | Print bed temperature | 40-60°C | | | + | | Print bed temperature | OFF-50°C | | |
| - | | Build chamber temperature | 20-40°C | [[{|width: 8em}#adjusting-the-build-chamber-temperature|Build chamber temperature]] | | + | | Build chamber temperature | OFF°C | [[{|width: 8em}#adjusting-the-build-chamber-temperature|Build chamber temperature]] | |
| - | | Extruder temperature | 180-235°C * | | | + | | Extruder temperature | 180-220°C * | | |
| - | | Speed settings | - reduce print speed (max. 20m/s for all perimeters) * | | | + | | Speed settings | standard settings for ABS; for filled materials, reduce speed * | | |
| | Idler lever preload | 4.0mm | [[{|width: 8em}reprap-industrial-v1:service-guide#extruder-idler-lever|Setting the idler lever preload]] | | | Idler lever preload | 4.0mm | [[{|width: 8em}reprap-industrial-v1:service-guide#extruder-idler-lever|Setting the idler lever preload]] | | ||
| - | | Nozzle tip | 0.5 or above | | | + | | Nozzle tip | all | | |
| *<wrap lo> depending on color, filler; test to find best suitable settings for your application.\\ For example: [[http://colorfabb.com|colorFabb's]] famous //woodfill// is best extruded at 225 °C with 12 mm/s for perimeters and 24 mm/s for the infill.</wrap> | *<wrap lo> depending on color, filler; test to find best suitable settings for your application.\\ For example: [[http://colorfabb.com|colorFabb's]] famous //woodfill// is best extruded at 225 °C with 12 mm/s for perimeters and 24 mm/s for the infill.</wrap> | ||
| Line 1159: | Line 1159: | ||
| | Solvent | Tetrahydrofuran <WRAP caution>**USE RESPONSIBLY!**\\ //Tetrahydrofuran can cause eye irritations and irritations of the respiratory system. Fumes are easily flammable.\\ Apply skin protection cream or wear protective gloves when handling the solvent. Do not empty into drains. Do not use near open flames or heat sources.\\ Observe the manufacturer's safety data sheet and make accessible to anyone handling tetrahydrofuran!//</WRAP> | | | | Solvent | Tetrahydrofuran <WRAP caution>**USE RESPONSIBLY!**\\ //Tetrahydrofuran can cause eye irritations and irritations of the respiratory system. Fumes are easily flammable.\\ Apply skin protection cream or wear protective gloves when handling the solvent. Do not empty into drains. Do not use near open flames or heat sources.\\ Observe the manufacturer's safety data sheet and make accessible to anyone handling tetrahydrofuran!//</WRAP> | | | ||
| | Layer binding | good | | | | Layer binding | good | | | ||
| - | | Part strength/stability | medium | | | + | | Part strength/stability | medium; parts are stiff and brittle | | |
| | Warping | low || | | Warping | low || | ||
| | Drying | not required | | | | Drying | not required | | | ||
reprap-industrial-v1/knowledge-base.txt · Last modified: 2017/01/18 09:51 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
