This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
reprap-industrial-v1:manual [2015/12/08 11:10] Markus Bürgener [Emergency stop] |
reprap-industrial-v1:manual [2015/12/11 08:46] Markus Bürgener [Electronic chamber] |
||
---|---|---|---|
Line 18: | Line 18: | ||
===== Valid Version ===== | ===== Valid Version ===== | ||
+ | ==== Hardware revisions ==== | ||
<WRAP group> | <WRAP group> | ||
<WRAP half column> | <WRAP half column> | ||
Line 31: | Line 32: | ||
* Serial number | * Serial number | ||
* Date of manufacturing | * Date of manufacturing | ||
- | * Hardware Revision | + | * Hardware Revision¹ |
- | Starting with version **1.1.0** of the [[software-version-v1.1.0-operation-and-commissioning| operating software RepRapOnRails]] you will also find the valid hardware revision in the [[software-version-v1.1.0-operation-and-commissioning#setup-menue|[Setup] ]] menu on the touchscreen.\\ | + | ¹<wrap lo> Starting with version **1.1.0** of the [[software-version-v1.1.0-operation-and-commissioning| operating software RepRapOnRails]] you will also find the valid hardware revision in the [[software-version-v1.1.0-operation-and-commissioning#setup-menue|[Setup] ]] menu on the touchscreen.</wrap> |
</WRAP> | </WRAP> | ||
Line 590: | Line 591: | ||
All control elements are installed in the electronic chamber together with the 12 V(DC) mains adapter and the cooling unit.\\ | All control elements are installed in the electronic chamber together with the 12 V(DC) mains adapter and the cooling unit.\\ | ||
+ | |||
The chamber is completely covered with plastic sheets fastened to the aluminum frame with hexagon socket screws and hammerhead nuts.\\ | The chamber is completely covered with plastic sheets fastened to the aluminum frame with hexagon socket screws and hammerhead nuts.\\ | ||
The MOSFET power switching board consists of five MOSFETs that switch the four heating resistors of the [[#Build chamber|build chamber]] heating and the heating resistor of the [[#Print table and print bed|print table]].\\ | The MOSFET power switching board consists of five MOSFETs that switch the four heating resistors of the [[#Build chamber|build chamber]] heating and the heating resistor of the [[#Print table and print bed|print table]].\\ | ||
+ | |||
The RUMBA board (also //reprap microcontroller board//) controls all processes of the printing process, i.e. the drives, the heating resistors, heating fans and the temperature sensors. Exchangeable hardware components are the stepper motor drivers.\\ | The RUMBA board (also //reprap microcontroller board//) controls all processes of the printing process, i.e. the drives, the heating resistors, heating fans and the temperature sensors. Exchangeable hardware components are the stepper motor drivers.\\ | ||
+ | |||
The BeagleBone Black embedded computer provides the GUI of the [[#Touchscreen|touchscreen]] and the ethernet connection and processes the G-codes of the slicing software.\\ | The BeagleBone Black embedded computer provides the GUI of the [[#Touchscreen|touchscreen]] and the ethernet connection and processes the G-codes of the slicing software.\\ | ||
Slots in the bottom cover provide an air inlet for the cooling unit. | Slots in the bottom cover provide an air inlet for the cooling unit. | ||
Line 632: | Line 636: | ||
At the rear cover you find the mains plug and the main switch of the mains adapter and the RJ45 ethernet plug for the network connection.\\ | At the rear cover you find the mains plug and the main switch of the mains adapter and the RJ45 ethernet plug for the network connection.\\ | ||
+ | |||
The cooling systems' accumulated warmth is dissipated via the radiator grill to the outside.\\ | The cooling systems' accumulated warmth is dissipated via the radiator grill to the outside.\\ | ||
- | The type plate is positioned next to the fixing screws of the cooling water pump, providing:\\ {{anchor:serialnumber:the serial number}}\\ the date of manufacturing and {{anchor:hardwarerevision:the hardware revision}}\\ as well as other necessary information about the 3D printer. | + | The [[#hardware-revisions|type plate]] is positioned next to the fixing screws of the cooling water pump. |
</WRAP> | </WRAP> | ||