reprap-industrial-v1:manual
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
reprap-industrial-v1:manual [2015/12/11 08:39] Markus Bürgener [Electronic chamber] links updated |
reprap-industrial-v1:manual [2016/07/08 07:56] Simon Kühling [Imprint] |
||
|---|---|---|---|
| Line 18: | Line 18: | ||
| ===== Valid Version ===== | ===== Valid Version ===== | ||
| + | ==== Hardware revisions ==== | ||
| <WRAP group> | <WRAP group> | ||
| <WRAP half column> | <WRAP half column> | ||
| Line 31: | Line 32: | ||
| * Serial number | * Serial number | ||
| * Date of manufacturing | * Date of manufacturing | ||
| - | * Hardware Revision | + | * Hardware Revision¹ |
| - | Starting with version **1.1.0** of the [[software-version-v1.1.0-operation-and-commissioning| operating software RepRapOnRails]] you will also find the valid hardware revision in the [[software-version-v1.1.0-operation-and-commissioning#setup-menue|[Setup] ]] menu on the touchscreen.\\ | + | ¹<wrap lo> Starting with version **1.1.0** of the [[software-version-v1.1.0-operation-and-commissioning| operating software RepRapOnRails]] you will also find the valid hardware revision in the [[software-version-v1.1.0-operation-and-commissioning#setup-menue|[Setup] ]] menu on the touchscreen.</wrap> |
| </WRAP> | </WRAP> | ||
| Line 737: | Line 738: | ||
| The transport box is made of unfinished plywood and may hold splinters and sharp edges that can cause cutting injuries. | The transport box is made of unfinished plywood and may hold splinters and sharp edges that can cause cutting injuries. | ||
| * Take care when removing the transport packaging and wear protective gloves. | * Take care when removing the transport packaging and wear protective gloves. | ||
| + | </WRAP> | ||
| + | |||
| + | <WRAP note> | ||
| + | NOTE | ||
| + | |||
| + | If the 3D Printer has a temperature below 16°C (e.g. directly after delivery in cold weather) there is a danger of air humidity condensing on sensitive electronic components. This can lead to severe damages due to short circuiting during commissioning.\\ Therefore, it is necessary to let the 3D Printer warm up to ambient temperature at its operating place prior to commissioning.\\ Regard the [[technical-data#td-ac|ambient conditions]] required for operation. | ||
| </WRAP> | </WRAP> | ||
| Line 842: | Line 849: | ||
| ====== Imprint ====== | ====== Imprint ====== | ||
| - | //Jonas Kühling & Simon Kühling GbR\\ | + | // Kühling&Kühling GmbH\\ |
| - | Im Wiesengrund 23\\ | + | Christianspries 30\\ |
| - | 24113 Molfsee\\ | + | 24159 Kiel\\ |
| Deutschland\\ | Deutschland\\ | ||
| E-Mail: office@kuehlingkuehling.de\\ | E-Mail: office@kuehlingkuehling.de\\ | ||
| Tel.: +49 (0) 431 98 35 24 73\\ | Tel.: +49 (0) 431 98 35 24 73\\ | ||
| \\ | \\ | ||
| - | Handelsregister\\ | + | Local Court: Amtsgericht Kiel\\ |
| - | USt.-Ident.-Nr.: DE283006938\\ | + | Commercial Register No.: HRB 17535\\ |
| - | WEEE-Reg.-Nr.: DE 11304600\\ | + | Managing Directors: Jonas Kühling, Simon Kühling, Karsten Wenige\\ |
| - | \\ | + | VAT Reg.No.: DE305873054 |
| - | Geschäftsführer\\ | + | |
| - | Jonas Kühling\\ | + | |
| - | Simon Kühling// | + | |
reprap-industrial-v1/manual.txt · Last modified: 2016/07/08 08:02 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
