reprap-industrial-v1:service-guide
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
reprap-industrial-v1:service-guide [2015/10/30 11:07] Markus Bürgener [Cleaning recommendation] |
reprap-industrial-v1:service-guide [2015/11/02 07:59] Markus Bürgener [Replacing the heating block] |
||
|---|---|---|---|
| Line 335: | Line 335: | ||
| * pipe cleaner | * pipe cleaner | ||
| === Additional information === | === Additional information === | ||
| - | * Disassembly / re-installation of nozzle and barrel -> [[#Dissembling / re-installing the hot end nozzle tips and/or barrels|Service guide]] | + | [[{|width: 25em}#dissemblingre-installing-the-hot-end-nozzle-tips-andor-barrels|Disassembly / re-installation of nozzle and barrel]]\\ |
| - | * Suitable solvents -> [[reprap-industrial-v1:knowledge-base#materials|Knowledge base]] | + | [[{|width: 25em}reprap-industrial-v1:knowledge-base#materials|Suitable solvents]]\\ |
| - | * Removing / reinserting filament -> Software manual [[Software version v1.0.5 - Operation and commissioning#Changing the filament|v1.0.5]] or Software manual [[Software version v1.1.0 - Operation and commissioning#Changing the filament|v1.1.0]]; | + | [[{|width: 25em}Software version v1.1.0 - Operation and commissioning#Changing the filament|Changing the filament]] | |
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
| Line 428: | Line 428: | ||
| === Additional information === | === Additional information === | ||
| - | * Software manual [[Software version v1.0.5 - Operation and commissioning#Manual Control|v1.0.5]] | + | [[{|width: 10em}software-version-v1.1.0-operation-and-commissioning#expert-control-screen|Software manual]] |
| - | * Software manual [[Software version v1.1.0 - Operation and commissioning#Print|v1.1.0]] | + | |
| === Removing === | === Removing === | ||
| Line 497: | Line 496: | ||
| === Additional information === | === Additional information === | ||
| {{anchor:sg02}} | {{anchor:sg02}} | ||
| - | * [[#Cleaning recommendation|]] | + | [[{|width: 15em}#Cleaning recommendation|Cleaning recommendation]]\\ |
| - | * Software manual: [[reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc131|filament change]], [[reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc14t05|expert control]] | + | [[{|width: 15em}reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc131|Software manual - filament change]] [[{|width: 15em}reprap-industrial-v1:software-version-v1.1.0-operation-and-commissioning#omc14t05|Software manual - expert control]] |
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
| Line 686: | Line 685: | ||
| * Allen wrench #1.5 | * Allen wrench #1.5 | ||
| - | === Accompanying information === | + | === Additional information === |
| - | * Troubleshooting: [[reprap-industrial-v1:troubleshooting#p9|P9]], [[reprap-industrial-v1:troubleshooting#em1|EM1]] | + | [[{|width: 10em}reprap-industrial-v1:troubleshooting#p9|Troubleshooting P9]]\\ |
| + | [[{|width: 10em}reprap-industrial-v1:troubleshooting#em1|Troubleshooting EM1]] | ||
| === Heating block exchange procedure === | === Heating block exchange procedure === | ||
reprap-industrial-v1/service-guide.txt · Last modified: 2017/01/18 09:52 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
