vp75:general
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
vp75:general [2017/01/10 11:43] Simon Kühling ↷ Links adapted because of a move operation |
vp75:general [2017/01/18 11:13] (current) Simon Kühling [Type plate] added typle plate example picture |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| <WRAP clear/> | <WRAP clear/> | ||
| Welcome to the operating manual for the VP75 Additive Manufacturing System of the Kühling&Kühling GmbH (in the following referred to as //Kühling&Kühling//).\\ | Welcome to the operating manual for the VP75 Additive Manufacturing System of the Kühling&Kühling GmbH (in the following referred to as //Kühling&Kühling//).\\ | ||
| - | The VP75 Additive Manufacturing System (in the following referred to as //VP75// or //machine//) is a fully automatic stand-alone device for **F**used-**F**ilament-**F**abrication (FFF) in a lab or commercial environment.\\ Any information needed for [[#setup-and-installation|installing and commissioning]], [[#touchscreen-operation|operating]], [[#troubleshooting|]], [[:service-guide|maintenance and repair]] of the AMS are described in the following paragraphs and the accompanying sites.\\ | + | The VP75 Additive Manufacturing System (in the following referred to as //VP75// or //machine//) is a fully automatic stand-alone device for **F**used-**F**ilament-**F**abrication (FFF) in a lab or commercial environment.\\ Any information needed for [[#setup-and-installation|installing and commissioning]], [[#touchscreen-operation|operating]], [[#troubleshooting|]], [[:service-guide|maintenance and repair]] of the machine are described in the following paragraphs and the accompanying sites.\\ |
| This user's manual must be read thoroughly as it is meant to provide the operator with all information needed to operate the VP75 safely and reasonably. Please always provide access to the website for any user of the Additive Manufacturing System in case of questions or problems. | This user's manual must be read thoroughly as it is meant to provide the operator with all information needed to operate the VP75 safely and reasonably. Please always provide access to the website for any user of the Additive Manufacturing System in case of questions or problems. | ||
| <WRAP clear></WRAP> | <WRAP clear></WRAP> | ||
| Line 73: | Line 73: | ||
| <WRAP half column> | <WRAP half column> | ||
| - | [{{fehlendegrafik.png?100|Type plate on the rear side.}}] | + | [{{nameplate-example.png?400|Type plate on the rear side.}}] |
| <WRAP clear/> | <WRAP clear/> | ||
| |<93% 15%>| | |<93% 15%>| | ||
| Line 79: | Line 79: | ||
| | 2 | Date of manufacturing | | | 2 | Date of manufacturing | | ||
| | 3 | Hardware Revision | | | 3 | Hardware Revision | | ||
| - | </WRAP> | ||
| - | </WRAP> | ||
| - | |||
| - | |||
| - | ===== Warning signs and labels ===== | ||
| - | <WRAP group> | ||
| - | <WRAP half column> | ||
| - | Due to the manufacturing process single components inside the build chamber may reach temperatures up to 500 °C. To warn the operator before touching anything inside the machine, areas of high temperatures are specially marked. | ||
| - | </WRAP> | ||
| - | |||
| - | <WRAP half column> | ||
| - | [{{hotsurfaces.png?100|Hot surface warning sign.}}] | ||
| - | </WRAP> | ||
| - | </WRAP> | ||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP half column> | ||
| - | Current carrying components are labeled specially to indicate the danger of electric shocks. | ||
| - | </WRAP> | ||
| - | |||
| - | <WRAP half column> | ||
| - | [{{highvoltage.png?100|High-voltage label on current carrying parts.}}] | ||
| </WRAP> | </WRAP> | ||
| </WRAP> | </WRAP> | ||
| ====== Intended use ====== | ====== Intended use ====== | ||
| - | The VP75 Additive Manufacturing System has been designed and built for manufacturing three-dimensional workpieces of nearly random geometries from common 1.75 mm thermoplastic filament strands.\\ The AMS features an advanced hot-end geometry with an extrusion temperature up to 500°C. In combination with the heated build chamber (up to 70°C) and the heated built plate (up to 130°C), this makes the VP75 suitable for processing a variety of materials. It is therefor capable of performing regular additive manufacturing tasks with standard thermoplastics as well as special jobs with technical plastics.\\ | + | The VP75 Additive Manufacturing System has been designed and built for manufacturing three-dimensional workpieces of nearly random geometries from common 1.75 mm thermoplastic filament strands.\\ The machine features an advanced hot-end geometry with an extrusion temperature up to 500°C. In combination with the heated build chamber (up to 80°C) and the heated built plate (up to 150°C), this makes the VP75 suitable for processing a variety of materials. It is therefor capable of performing regular additive manufacturing tasks with standard thermoplastics as well as special jobs with technical plastics.\\ |
| - | [[http://kuehlingkuehling.de/imprint/|Contact]] //Kühling&Kühling// or refer to [[http://kuehlingkuehling.de/product-category/consumables/|our web shop]] for more detailed information on available and applicable materials. | + | [[http://kuehlingkuehling.de/imprint/|Contact]] //Kühling&Kühling// for more detailed information on available and applicable materials. |
| The VP75 is intended for industrial and commercial use. It is not valid for the operation in an explosive atmosphere.\\ | The VP75 is intended for industrial and commercial use. It is not valid for the operation in an explosive atmosphere.\\ | ||
| Observing this manual and adhering to the stated information is part of the proper operation.\\ | Observing this manual and adhering to the stated information is part of the proper operation.\\ | ||
| Improper operation of the VP75 can lead to hazardous situations.\\ | Improper operation of the VP75 can lead to hazardous situations.\\ | ||
| - | It is forbidden to operate the AMS under conditions and for purposes other than stated in this manual. | + | It is forbidden to operate the machine under conditions and for purposes other than stated in this manual. |
| Operating the VP75 is forbidden under the following circumstances: | Operating the VP75 is forbidden under the following circumstances: | ||
| * The VP75 is used for a purpose not designated, with unspecified materials or out of its operating range in any other way. | * The VP75 is used for a purpose not designated, with unspecified materials or out of its operating range in any other way. | ||
| * Mechanical parts or parts of the electrical equipment are damaged or the insulation is defective. | * Mechanical parts or parts of the electrical equipment are damaged or the insulation is defective. | ||
| - | * The VP75 does not function flawless. | + | * The VP75 does not function flawlessly. |
| * Mechanical components or the control system have been inexpertly altered or reconstructed. | * Mechanical components or the control system have been inexpertly altered or reconstructed. | ||
| * Operating parameter have been altered inadmissibly. | * Operating parameter have been altered inadmissibly. | ||
| Line 134: | Line 112: | ||
| * operation beyond the specified operating parameters | * operation beyond the specified operating parameters | ||
| * false setup, commissioning, operation repair or maintenance | * false setup, commissioning, operation repair or maintenance | ||
| - | * operating the AMS with defective, missing, improperly installed and/or malfunctioning equipment | + | * operating the machine with defective, missing, improperly installed and/or malfunctioning equipment |
| * unauthorized or inadmissible alteration of the electrical or mechanical equipment or the operating parameters of the system. | * unauthorized or inadmissible alteration of the electrical or mechanical equipment or the operating parameters of the system. | ||
| * use of other than the specified replacement parts, tools, and/or operating materials | * use of other than the specified replacement parts, tools, and/or operating materials | ||
| Line 152: | Line 130: | ||
| ====== Ordering wear and spare parts and material ====== | ====== Ordering wear and spare parts and material ====== | ||
| - | Parts of the VP75 are subject to wear and must be replaced in the specified intervals or on demand. Regularly check these components as stated in the maintenance manual and replace them if required.\\ Using the VP75 with worn parts is forbidden and frees //Kuehling&Kuehling// from liability.\\ | + | Parts of the VP75 are subject to wear and must be replaced in the specified intervals or on demand. Regularly check these components as stated in the maintenance manual and replace them if required.\\ Using the VP75 with worn parts is forbidden and frees //Kühling&Kühling// from liability.\\ |
| Wear parts must meet the technical specifications defined by //Kühling&Kühling//. //Kühling&Kühling// original parts are subject to rigid requirements and meet these standards.\\ | Wear parts must meet the technical specifications defined by //Kühling&Kühling//. //Kühling&Kühling// original parts are subject to rigid requirements and meet these standards.\\ | ||
| Contact [[sales@kuehlingkuehling.de]] for complete list of available wear and spare parts.\\ \\ | Contact [[sales@kuehlingkuehling.de]] for complete list of available wear and spare parts.\\ \\ | ||
| Line 176: | Line 154: | ||
| Simon Kühling\\ | Simon Kühling\\ | ||
| Karsten Wenige// | Karsten Wenige// | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
vp75/general.1484048582.txt.gz · Last modified: 2017/01/10 11:43 by Simon Kühling
Except where otherwise noted, content on this wiki is licensed under the following license: Creative Commons Attribution-ShareAlike 4.0 International License
